2019 BMW X5 Complaint Log

My daughter was driving my BMW X5, it went to neutral and not moving, she was panicked and stopped the car and ignition. After restarting the car, it worked for a day, then it happened again, also, I see notifications on dashboard for restraint warning, saying, airbag, and seat belt tension are reduced. I took to Fairfax BMW in VA, BMW quoted $2662, informed that my BMW went out of extended warranty over a month, I asked Goodwill request to BMW, still declined.

I recently took my 2019 X5 to the BMW dealership because of the recall (Engine starter) and the code P0456 (NVLD Minor Leak Fault). At the same time, there's a warning that says, "Oil at a minimum level. Add 1 liter immediately". I have the 3 Year Oil Plan and asked them to put some oil, but the dealership said that they can't add oil because the oil level wouldn’t read properly. They told me they couldn’t diagnose it without charging me an extra 300 for further testing. Then, I read a lot of threads online and it seems that BMW quietly changed the pump to an all-metal design around 2020 but never issued a recall or extended warranty for the earlier cars. There's a lot of customers complaining with the B58TU engine found in many 2019–2021 BMWs (X5 xDrive40i, 540i, 340i, etc.). The variable oil pump uses a plastic internal adjusting ring that cracks over time. When it fails, oil pressure becomes unstable or is lost, often with little warning. A common early symptom is the oil level sensor test failing and stopping around 12-20%. In the worst cases, it can lead to sudden engine damage or the car shutting down while driving. I called up my mechanic, and he said that this is a common problem and it could be an oil pump issue that needs to be replaced. I asked him for a quote and he said approximately 5k or more. I believe this is a safety defect that deserves investigation Hoping for your kind consideration. I plan to keep my car as long as possible Thanks, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2019 BMW X5. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly overheated, and the engine temperature warning light illuminated. The vehicle was taken to a dealer, where it was diagnosed that the coolant line to the cylinder had failed and needed to be replaced. The vehicle was repaired. The contact later received notification of NHTSA Campaign Number: 25V644 (Electrical System). The manufacturer was not made aware of the failure. The approximate failure mileage was 101,187.

The starter on my BMW failed, and it overheated and damaged my alternator to the point that I needed to replace it. The dealer and independent service center confirmed that this was the cause, but BMW is refusing to reimburse the cost of the alternator replacement. I was at the exit of a highway and could not even put the car in neutral, so my safety was significantly at risk.

Emergency call system malfunction. Vehicle available for inspection. Warning appears and verified by dealer as common issue with vehicle type due to shark fin antenna seal leaks, causing corrosion in the module when in contact with water (including rain). Cause loss of GPS and wireless capability.

I am writing to report a significant safety issue associated with BMW vehicles equipped with the B58TU engine, particularly the 2019-2021 models. These vehicles feature an oil pump containing an internal plastic component responsible for regulating oil pressure. There have been numerous instances of this part fracturing in the field, leading to a sudden loss of oil pressure. The failure predominantly occurs during cold starts in low temperatures. When this occurs, oil pressure can fluctuate erratically or be lost completely, often with minimal warning. Potential warning signs include difficulties in electronically measuring the oil level, abnormal oil pressure readings, or sudden drivetrain malfunction alerts. These issues can escalate quickly, resulting in engine shutdown or severe damage due to oil starvation. This situation poses a serious risk, as the vehicle may become inoperable without warning while driving or immediately after startup. Such failures are particularly hazardous when vehicles become immobilized in traffic or during winter conditions, leaving occupants vulnerable to harsh temperatures while awaiting roadside assistance. The replacement of the oil pump necessitates extensive disassembly and typically incurs a cost of $6,000-$8,000, assuming no engine damage has occurred. A significant concern is that owners cannot easily ascertain whether their vehicle is equipped with the original plastic pump or a revised metal component. BMW's VIN-based parts lookup now indicates updated components even if the original plastic parts are still installed. Additionally, the original plastic part number has been removed from dealer networks. Failures have been reported across multiple production years, and the full extent of affected vehicles remains uncertain. Given that this condition can lead to abrupt vehicle disablement without adequate warning—especially in cold weather—this situation warrants investigation as a potential safety-related defect.

The contact owns a 2019 BMW X5. The contact stated that while driving approximately 45 MPH, the red oil light suddenly illuminated and the messages "Stop Carefully and Turn Off Engine", “Engine Oil Pressure Too Low", "Continued Driving will Result in Engine Damage". The vehicle was towed to the local mechanic, who discovered that the engine oil was black and thick. The vehicle was later towed to the local dealer, who confirmed that the engine oil was thick and dark, and the engine needed to be replaced. The failure mileage was 85,000.

Premature oil pump failure. 2019 BMW x5 with only 46k miles has been diagnosed with an oil pump failure. Vehicle needed to be quickly pulled over and shut off to avoid catastrophic engine failure or engine seize. If this happens on the highway or at any speed the vehicle will lose power and be unsafe to control likely ending in an accident. This is a known Issue. BMW produced the vehicle with a flawed oil pump design that has a plastic ring around the impeller. The ring deteriorates and cracks leading to pump failure and loss of oil pressure It is only on limited models early 2019 X5. BMW redesigned with an all metal pump quietly. This issue needs to be addressed with BMW as it is unsafe for these family vehicles to be on the road with such a significant risk to its passengers and others. The failure happens with little to no warning. When contacting BMW they told me they would not consider helping with repairs. The repair for this part is upward of $8k which in turn will likely limit consumers ability to fix proactively. This is totally unacceptable and needs to be addressed by the NHTSA directly with BMW. P

BMW knowingly did NOT NOTIFY it's 2019 BMW X5 M40i (engine B58) vehicle owners. This is in reference to the faulty design and made plastic engine oil pump. It has been known to fail prematurely due to weaken parts. Some analysis done was from certain oil viscosity's applying additional unneeded stressful pressures. This later was recognized by BMW and a newer design and/or metal sturdier one had taken it's place in subsequent model years starting in 2020. Some owners were able to remediate the oil pump failure and new replacement either covered under intact warranties, and some were covered through quieter negotiations with BMW Customer Care's authorizations. To my understanding, no recalls were made nor were any techical service bulletins (TSB) made to it's owners. I don't see how BMW can be allowed to get away with an issue of safety which could cause a catastrophic failure of the affected engine? Under the circumstances, BMW should be fully reimbursing me for the repairs here, and be glad there were NO serious injuries OR worse, DEATHS! I have been in contact with their Customer Care and nothing has been done to date.

I bought the car from the dealership, and they said there were no problems with it, but they cheated me. The car broke down twice. The first time, it was parked in a private lot for several hours, and I paid a large sum for parking. The second time, it broke down on the street, and I waited eight hours for help to tow it back to the dealership. 1-recall message 2- emergency call system

Engine Starter overheating. Car won't start until engine cools down. Car would not let my shift into neutral in order to move to a safe location. Was stuck in front of several cars in an unsafe location. No warning message showed up. Car was just inspected and serviced with no indication that this was a problem. Car taken to dealer after incident and inspected produced the same results.

Subject: 2019 BMW X5 xDrive40i – Oil Pump Defect Causing Oil Measurement Failure and Safety Risk I am reporting a safety defect in my 2019 BMW X5 xDrive40i with the 3.0L B58 inline-6 engine. The vehicle currently has approximately 70,000 miles. The vehicle is unable to properly measure or display engine oil level due to incorrect oil readings, which have been attributed to a failing oil pump assembly containing internal plastic components. Because this vehicle does not have a traditional dipstick, the electronic oil level monitoring system is the only way to verify proper oil level. Due to the defective oil pump design, I am unable to confirm whether the engine has sufficient oil. This creates a serious safety concern because: •The vehicle may be operating with low oil pressure without accurate warning •Sudden oil pressure loss could cause engine shutdown while driving •Loss of power at highway speeds could result in an accident •Catastrophic engine failure could occur without proper oil monitoring This is not normal wear and tear. BMW has reportedly updated the oil pump design in newer model years to use metal internal components, suggesting awareness of a design weakness. However, no recall has been issued for 2019 models. An oil pump that prevents accurate oil level measurement and may fail prematurely presents a significant safety hazard. I respectfully request that this defect be formally investigated and that BMW be required to issue a recall to replace the defective oil pump assembly with the updated metal design.

Transfer case on 2019 X5,yes available for inspection upon request. At stop position making right turn or left turn the vehicle jutters,also in reverse. Yes - confirmed by the bmw service center who tried to charge for diagnostic fee. Manufacturer knows of issue on 2019 X5 models. Video of these transfer case issues all over online in videos. Issue started about 6 - 9 months ago.

I am reporting a serious safety defect involving the oil pump assembly on my 2019 BMW X5 xDrive40i. While driving at low speed in normal conditions, a sudden dashboard warning appeared stating: “Engine oil pressure too low — stop carefully.” I immediately pulled over and shut off the engine. My vehicle had been serviced by an authorized BMW dealership less than one week earlier, and no faults or issues were identified. There were no warning signs or symptoms prior to the failure. An independent licensed repair facility inspected the vehicle after the incident and confirmed that the oil pump had failed due to a defective plastic internal component used in the pump’s design. The failed parts are available for inspection upon request. This failure created a significant safety risk, as sudden loss of oil pressure can cause engine seizure, loss of power steering, loss of braking assist, and an inability to safely control the vehicle. Had this occurred at highway speeds, the consequences could have been severe. I have since learned that this exact issue has been reported by other owners of 2019 BMW X5 vehicles and other BMW models using the B58 engine, which were equipped with an oil pump containing plastic internal drive components prone to cracking or separating. BMW appears to have updated the oil pump design to a metal version in 2020 and later models, suggesting the manufacturer was aware of the weakness of the earlier design. The defect was confirmed by an independent service center. The vehicle had also been inspected by BMW one week prior during scheduled service, yet no issues were detected. Because this failure presents a clear safety hazard and appears to be related to a widespread design flaw, I respectfully request that NHTSA open an investigation into the oil pump used in 2019 BMW X5 vehicles and consider issuing a safety recall.

The engine warning system came on and warned of low oil pressure. Knowing the oil level was good I stopped the vehicle to check oil leaks. Found none. Knowing engine mechanics I assumed it was a faulty oil pump. had it towed to BMW and told it was so. The replacement would be $8,000. Found out after lengthy research that the oil pump of the 2019 X5 (which I have) was made with plastic internal parts that would be a matter of when not if, the plastic parts would fail because the acidic nature of used oil. Presented this info to BMW and they lowered the price to $3986.16. Then I discovered BMW knew about the problem and changed the oil pump design from 2020 on.

a concern regarding my BMW x5 it’s a 2019 x50i it’s my only vehicle that I have to get to and from work and drive my family around. I have been having starting issues at random times I can go a week no issues than randomly. My vehicle doesn’t want to start. Also, I have engine codes that are the same ones that apply to other recalls my starter is my main concern because it is an unsafe situation in certain circumstances because it’s happened at a light due to the auto stop switch I have to turn it off so that problem wouldn’t occur anymore because it also happened on the freeway during traffic that was a scary scenario when I had my family with me luckily it did turn on as I was steering out the way of traffic, I love the car unfortunately it is giving me safety concerns ,I seen there is a recall on NHTSA Campaign Number: 24V-576 subject : Starter Motor May Fail and Overheat according to this my vehicle meets all these criteria’s I need help with further assistance please if you can and thank you for your time.

gas pedal broke while driving on the interstate causing driver to briefly lose control of car at the same time signal was lost from pedal to engine resulting in surge in the coolant system via ECm computer that blew radiator hose a moment after pedal broke. Pulled over and had car towed.

Car wouldn't start anymore, starter malfunction. couldnt go into neutral

I bought the car 8 months ago from Fred Anderson Acura in Greenville was told the car was inspected and serviced and I’m was in great condition. 8 months later I have 10 thousand worth safety issues wrong with the car that I have to fix .

My shark fin has water damage and can’t drive or be in rain and this is the only car I have to take my young kids back and forth to school and do my grocery shopping or whatever I need

The shark fin is leaking and can’t be in rain or drive in rain bc it can cause wires to catch fire or shorten out. I have two babies that are at risk every time I drive this car. It’s my only way to go and BMW won’t fix it and I can’t afford to fix it bc it’s over 3 thousand dollars.

MY STARTER MOTOR OVERHEATED AND MY CAR WOULD NOT START AND MY CAR INDICATED THE FLUIDS AND COMPONENTS WERE OVERHEATED - MY DEALERSHIP CONFIRMED THE PROBLEM WITH A VIDEO THEY SENT ME. IF I WAS STILL DRIVING THE CAR, I DON'T KNOW WHAT WOULD HAVE HAPPENED TO ME MY DAUGHTER AND HUSBAND IN THE VEHICLE. i CALLED MY SERVICE REP AND THE DEALERSHIP IS LOOKING INTO IT AS MY VIN DOES NOT HAVE THE RECALL. NOTHING WAS WRONG AND NO LIGHTS WERE ON THE VEHICLE PRIOR TO THE CAR NOT STARTING. I HAD BEEN DRIVING IT FOR ABOUT 25 MINUTES. In MAY of this year, not even 6 months ago, they had to replace a "heat management module", which cost me $2500 and they said it is not related. They found 8 fault codes at a frequency of 255. The dealership is telling me this is not related, but I have a hard time believing that.

I noticed one of my daytime running lights on the driver’s side laser headlight had turned yellow, instead of white like the others. I took the vehicle to the dealership and they said that the LED module that powers that daytime running light has overheated and caused the light tube to burn and melt. The dealership advised that the passenger side is also slowly starting to do the same thing. The repair the dealership recommended is to replace both headlights, at a cost of almost $18k! I’ve seen numerous BMWs on the roads with this same issue, and this should be addressed by BMW as a design flaw. If these modules are burning plastic pieces inside the housing, they could start a fire if they get hot enough.

While driving down the Long Island Expressway at around 60 miles per hour, the retractable part of my panoramic sun roof shattered. It felt like an explosion. Luckily, the sunroof and cloth cover was fully extended so the glass didn't fall in the car. The traffic was light, no one in front of me and wasn't driving under any structure. There were no construction or debris on the road. It's clearly a manufacturer defect. Thanks, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The automatic emergency braking is activating when nothing is on the road. It has happened three times in six months. Once in a drive thru, once in the middle of a clear intersection while moving at 30pmh and today while traveling at 35mph on a city street. The car acts as if it's attempting to prevent a forward collision. The red car icon displays and blinks on the instrument panel, fast beeps sound, the car hard brakes. It nearly caused the car behind me to rear end me today.

Frequent Passenger Restraint System Issue

The contact owns a 2019 BMW X5. The contact stated that while his wife was driving approximately 30-40 MPH, the message “Low Engine Oil” and to pull over to avoid engine destruction was displayed. The driver pulled over. The vehicle was towed to the dealer, where it was diagnosed, and determined that the internal parts of the oil filter made of plastic had deteriorated. The dealer determined that the engine needed to be taken apart to replace the filter. The vehicle was repaired. The manufacturer was notified of the failure and covered half the cost of the repair. The failure mileage was approximately 80,000.

The electronic oil level sensor was unable to complete an oil level measurement on the iDrive screen. Diagnostic inspection at a BMW Dealership (Mt. Kiso) and EuroTech Auto Repair (Larchmont, NY) revealed that the oil pump had degraded internally, specifically due to failure of plastic components. All Sensors were working fine and showed no faults. This failure could not be detected by regular maintenance and posed a risk to engine reliability and potential sudden loss of lubrication. The car had approx 55,000 miles, was purchased purchased after my 3-year lease (original owner of new vehicle), and the incident occurred during normal use. There were no warning lights or symptoms before the oil measurement stopped working. This defect appears to be a design/materials issue affecting other similar vehicles. The failed oil pump has been replaced at my expense. I am concerned this part presents a broader safety and reliability risk and should be considered for recall.

Emergency Call System Failure!! My 2019 BMW x5 xdrive M50 has the failure from the Telematic Control Module like thousands of other people. This needs to be a recall and shouldn’t have to pay $1500-3000 out of pocket for something that is a manufacture problem. Apparently water gets in the shark fin area and causing the module to fail!

The contact owns a 2019 BMW X5. The contact stated that while attempting to cold-start the vehicle, the contact needed several attempts to start the vehicle. The contact stated that several times, the contact was unable to restart the vehicle. The contact stated that while making several attempts to start the vehicle, the message "System Overheated - Restarting Engine Possible After Cooling" was displayed on the instrument cluster, and the contact had to wait 120 seconds before further attempts to restart the vehicle were possible. The contact had taken the vehicle to a local dealer, where it was diagnosed, and determined that the starter needed to be replaced. The vehicle was not repaired. The contact was informed by the dealer that there was a recall for the failure, NHTSA Campaign Number: 25V644000 (Electrical System), and the VIN was covered under the recall. However, the VIN tool showed no recall related to the VIN. The manufacturer was informed of the failure. The failure mileage was approximately 80,000.

Car randomly wouldn’t start and was getting error starter message on message center

Failed components 1. oil pump $8769.41 2. Cylinder Head Assembly- Valve Cover $4280.83 3. center console control panel $3051.93 4. transfer case replacement TBD 2019 BMW X5 xDrive40i has multiple major component failures at 70,000 miles. Oil pump failed causing loss of oil-level monitoring. The cylinder head assembly was diagnosed with oil consumption, the transfer case exhibited driveline shuddering, and the center console control panel developed internal electrical faults that affect vital vehicle components. All have been diagnosed by BMW of North Haven, CT. The oil pump and transfer case failures have created potential loss of engine lubrication and vehicle control putting my safety at risk. The oil-level test aborts at 16% making it impossible to verify oil quantity or pressure while driving. The shuddering occurs during low-speed turns and acceleration. BMW North America reviewed my case and approved goodwill coverage for transfer-case fluid change ALL other safety-related repairs have been denied. Supporting BMW Service Bulletins: •SIB 27 02 20: Jerking or Shuddering from Driveline xDrive Transfer Case ATX13-X (faulty factory oil specification). •SIB 11 03 17: N20/N26 Engine Timing Chain and Oil-Pump Drive Chain Warranty Extension (pattern of oil-pump failures in prior engines). •SIB B01 13 23: Front Center Console Cupholder Liquid Ingress (electrical faults from liquid intrusion in 2019–2022 G05 X5). •SIB 65 12 22: Roof-Mounted Antenna Housing Seal Not Adhering (water ingress from shark-fin antenna affecting interior electronics). Note: I paid out of pocket to replace and reprogram theTelematics Communication Box (TCB) due to faulty seal around shark fin. A class action lawsuit is currently in happening for this exact issue in California. These issues are not normal wear and tear. They represent premature mechanical and electrical failures on a well-maintained vehicle as well as posing a safety risk to me and other drivers.

The AC evaporator failed due to a known manufacturing defect common across the BMW G-chassis platform (G05, G07, G30). This has created two severe safety hazards: The refrigerant leak causes the windshield to fog up instantly and unexpectedly while driving, completely obstructing my visibility and nearly causing an accident. Chemical fumes and oil from the leaking evaporator are entering the cabin through the vents, causing dizziness and respiratory irritation for the occupants. BMW is aware of this systemic issue through numerous owner reports and petitions but refuses to issue a recall or provide assistance. This is a critical component failure that directly impacts vehicle safety and occupant health.

Recently purchased a 2019 BMW X5 xdrive40i with 77k miles, after only owning for 3 weeks after a heavy rain storm. My dash lit up with “Emergency call system malfunction”, upon review online it seems to be a common issue with these BMW models and no recall has been issued. The sos malfunction causes the vehicle not to function properly and unable to use the integrated idrive head unit system. It also dials emergency services on its own and won’t let me end call. After taking it to bmw dealership they found the telematics module battery to be low and suggested replacing. Previous owner had similar issue back in January of 2023 and the shark fin antenna by the roof was replaced , resealed and TCB telematics unit replaced. So only after 2 weeks of replacing the TCB battery, same issue appeared again after a heavy rain storm. I took it back to bmw for diagnose and they had to have one of there engineers test it and found out the actual sos button ecu system unit to have a short causing the sos malfunction and it dialing emergency services on its own. Vehicle is not driveable and has been at bmw they are trying to charge me additional $1,547.58 plus taxes and fees for the repair. I feel as if this is a defect on bmw and should be addressed and issued as an recall for there customers.

Known issue regarding failing oil pump in BMW B58 engines.

The oil pump contains a plastic housing that fractured during regular use. (Yes, I did retain the part for inspection and can include photos of the defect here). Yes, the problem has been confirmed by my mechanic and the general public with multiple posts and videos shared widely across the internet and in vehicle forums. This failure caused the engine to lose oil pressure abruptly. Had this occurred at highway speeds or in heavy traffic, it could have resulted in a serious accident. BMW is aware of the problem and has redesigned the oil pumps for all X5s starting in 2020. There is no real warning for this potential failure which would cause the engine to cease. The problem is most commonly diagnosed by checking the oil level via the I-Drive System electronically, (there is no dipstick for these cars). The oil level cannot be provided on the screen due to significant pressure fluctuations caused by the damaged oil pump- and that's how you know you're at risk of engine failure. There has been no recall for the 2019 vehicles. All 2019 BMWs with the B58 engine, (and the Toyota Supra), include this dangerous and expensive design flaw and I believe a recall should be issued; the majority of these cars are still on the road. I estimate the total number of cars to be 250,000 cars. My oil pump had to be replaced or the car would be rendered undriveable. The estimate from BMW dealership #1 exceeded $11,000; the estimate from BMW dealership #2 exceeded $8,000. The car has less than 70,000 miles on it and this is a known issue for this model year.

starter failed at 48k miles. This is a known issue of starters failing early and a recall should be done for all impacted cars. Currently there is only a subset that are recalled for software program update to prevent burning out the starter, but the starter itself is failing, and recall should be issued for replacing the starter [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I purchased a used BMW from a local dealership, unaware that the vehicle had unresolved safety and mechanical issues. Over time, I began experiencing repeated problems including: •Power loss and hesitation while driving •Malfunctioning engine and drivetrain components •Electrical system glitches including dashboard warnings that would disappear before I could document them The car has been in and out of shops for diagnostics, and no lasting fix has been found. These defects have created safety concerns for me and my children, as I transport them daily. The vehicle feels unsafe to operate. I believe I may have been sold a lemon and am now pursuing legal remedies, including this formal safety complaint to report the issue.

My car said it overheated and would not start. After about 4 hours it did start and I took it to the dealer. They are saying that the battery and starter need replacement. I read that there was a recall for this exact reason on some specific VINs for my car model and year. Even though mine doesn't fall under that category it seems like the same issue that was recalled for others. Doing some online searches it seems this issue has happened to quite a few people.

The emergency call warning on the dash was activated. GPS and Heads-up display no longer functioned correctly. BMW Dealership replaced TCB2 Box and battery at a cost of $2956.63. In researching this issue found numerous complaints from other owners. Contacted BMW and was told they were not responsible, car was out of warranty (4yr / 50,000 mi). This is an electronic component that is positioned in the least hostile environment of the vehicle. It has NO moving parts, is located in a dry / protected area (above the headliner), has NO knobs to turn / buttons to push / or screens to touch and is not subject to normal wear and tear. One of 2 things seem to be the case: This is a rare failure of this component - in which case I would think BMW and the manufacturer would be not only interested to investigate but also responsible. This is a regular failure of this component and since it is an integral part of the car's safety system BMW does not want to acknowledge a known defect.

Car started hesitating to start then messaged popped up on screen saying my system was overheating I had to pay for a new starter.

The contact owns a 2019 BMW X5. The contact stated while the vehicle was parked, the vehicle failed to start as intended. No warning light was illuminated. The vehicle was towed to the dealer where it was diagnosed with a failed alternator. The contact was informed that the alternator needed to be replaced. The vehicle was not repaired. The contact referenced an unknown recall repair; however, the VIN was not included. The manufacturer was not made aware of the failure. The failure mileage was approximately 49,302.

While driving in the city, I came across a red light. When the light turned green, my car's engine shut off and the power steering turned off (unable to turn). The screen remained on but I could not start the car. This has only happened in the city when I am driving at a speed of up to 15 miles/hr. under comfort mode with the auto/stop feature on. This happened about 5 times on different dates where my car shut off but the screen was on. My car shut down in the middle of traffic, causing more traffic and an unsafe situation. Since then, I have turned off the auto/stop feature and have not yet encountered the problem again.

The vehicle's electrical system experienced a starter malfunction, which led to a complete failure of the starter. As a result, the car would not start, ultimately causing the battery to fail as well. This failure posed a serious safety risk. I could have been left stranded in the middle of traffic, increasing the risk of a collision that could have caused injury to myself and others. If the malfunction had occurred in a remote location, I could have been left stranded, placing me in a potentially dangerous situation. The issue was confirmed by the dealership. Although there is an active NHTSA recall related to this exact problem, my vehicle’s VIN was not included. However, it should have been—my vehicle was manufactured during the affected production period and experienced the same failure described in the recall. As a result, I had to pay out of pocket for these substantial repairs. The manufacturer failed to include my VIN in the recall, despite clear evidence that my vehicle was subject to the same defect. The manufacturer inspected the vehicle and confirmed that the failure involved both the starter and the battery; however, I was required to pay out of pocket for the replacement of both components. There were no warning lights, error messages, or other symptoms prior to the failure—the vehicle simply stopped functioning without notice. Further research revealed that many other owners have reported the same starter malfunction, frequently resulting in battery failure and the need to replace both components. Although the manufacturer is aware of this widespread issue, they have not issued a comprehensive recall for all affected vehicles. Had they done so, this failure—and the associated safety risks, inconvenience, and significant repair costs—could have been avoided.

The contact owns a 2019 BMW X5. The contact stated that while attempting to start the vehicle, the vehicle failed to start. There was no warning light illuminated. The vehicle was towed to a local dealer where the vehicle was diagnosed, and the contact was advised that the starter had failed and needed to be replaced. The vehicle was not repaired. The contact referenced NHTSA Campaign Number: 24V576000 (ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING) as a possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 80,100.

Vehicle Safety Complaint Report – BMW Engine Starter Failure Make: BMW Model: X5 xDrive40i Year: 2019 Mileage at Incident: ~40,000 km Component/System That Malfunctioned The engine starter system failed to function. Despite repeated attempts, the engine would not start. The vehicle showed no prior warnings or dashboard alerts before the failure. The part has not yet been replaced, and the car is unable to start still. Incident Description On a recent trip, while lined up at a ferry terminal waiting to board, our BMW X5 unexpectedly failed to start. There was no warning light or error code displayed. The car was completely unresponsive, despite repeated starting attempts. We were in the middle of the boarding line, blocking all vehicles behind us. We had to request assistance from ferry staff, who helped tow the car to a parkade. This incident led to the cancellation of our trip, caused significant stress and public disruption, and exposed us to serious safety and liability risks. We immediately contacted BMW roadside assistance, who were unable to diagnose the issue remotely and only suggested continued restart attempts, which were ineffective. We recently learned of NHTSA Recall 24V-576, issued on August 1, 2024, by BMW of North America. The recall involves the engine starter in 2019–2020 BMW X5 models, due to engine no-start issues and potential electrical overloads that can result in a thermal event. While our vehicle matches the make, model, and year, we were informed by BMW that our specific VIN is not currently listed under the recall. However, we are experiencing exactly the same problem described in the recall notice—an engine that suddenly fails to start, with no warning, and with the potential for unsafe repeated ignition attempts. I strongly believe that our vehicle should be included in BMW’s official recall list for 24V-576. The symptoms, risk profile, and component behavior align perfect with the recall description.

Vehicle didn’t move after coming to a full stop at a traffic light. And it displayed a message stating the starter has overheated and that it needed to cool down. The timer for the cooldown period kept on increasing up to 180 seconds and consequent attempts to start the vehicle after the cooldown period didn’t help.

Starter stopped working. VEHICLES Body Style : 2019-2020 BMW X5 (X5 sDrive40i, X5 xDrive40i) SUV Descriptive Information : Power Train : GAS Production Dates : Approximately 68,105 vehicles have been manufactured with an engine starter of a certain production configuration. Basis for recall population determination: Vehicle assembly information and supplier production records were used to determine the specific dates of potentially affected vehicles. Recall component difference to non-recall component: Potentially affected vehicles have an engine starter with a certain production configuration. AUG 01, 2018 - MAY 31, 2020 VIN Range 1 : Begin : NR End : NR Not sequential

Emergency call malfunction light came on. System is an important vehicle safety features. Vehicle taken to dealership for inspection. No visual damage present on vehicle however water ingress from roof shark fin is causing damage to electrical components, TCB and emergency call function. Shark fin antenna cover determined to be causing water ingress after inspection by BMW dealership. Per their recommendation, further water ingress could damage additional electrical components, some critical and therefore immediate need to replace TCB, Aerial antenna, and emergency battery. Vehicle warranty not covering this type of issue. Cost of repair estimated at $2500.

vehicle has been vibrating at low speeds when turning or when backing up. Took vehicle to BMW dealership (BMW of Nashville in Franklin, TN) multiple times during the past 18 months without resolution. On my visit for the same issue this month, dealership finally recognized the issue and said there was a BMW bulletin out about the issue SIB 27 02 20. It is very frustrating that 1. The dealership kept stalling and despite test driving the car with me and feeling the vibration, they kept blaming tires or saying it was normal while the bulletin about the issues was generated in 05.20.2020 2. It cost me over $627 for them to change the transfer case oil to diagnose and repair the issue. I am still in the testing phase after the transfer case oil change as the vehicle needs to be driven 300+ miles. The dealership and BMW should issue a recall since it is a know issue that the wrong oil was used in the manufacturing process and reimburse the cost charged for diagnostic and transfer case oil replacement. The vehicle is furthermore still under warranty so I should not be paying anything for diagnostics or repairs.