2018 Chrysler Pacifica Complaint Log

When taking turns the steering "sticks" amd it takes extra physical force to "unstick" the car. While unsticking by turning the steering wheel harder than normal, it either crosses into uncoming traffic or runs off the shoulder. It unsticks but with the extra physical force, it generally causes you to over correct and/or swerve/veer all over the roadway. 2018 with 72k miles

Steering has been sticking when making turns.

On our 2018 Pacifica the head gasket is blown. This seems to be a very common issue with the 2018 model that Chrysler won't address. No one was harmed. The problem was confirmed by our independent mechanic. No it has not been inspected by anyone other than the independent mechanic. The check engine light came on after a rough start, coolant level started to go down, and white smoke from the exhaust. There are many complaints and many forums with Pacifica owners needing to foot the bill for these repairs. There is specifically something wrong with this engine from this time frame. Thank you

The vehicle stalls while driving without any notice. This van has a start/stop function and it malfunctions. There are two separate batteries that control this function and both of them have been replaced. The entire steering rack and steering column have had to be replaced. The front suspension has also had to be replaced because the tires wear out very quickly. The alternator, radiator, and motor mounts have also had to be replaced. The van is available for inspection. At the moment the vehicle will not start and I have been advised that it needs a new starter. This vehicle is a safety risk and it puts others at risk as well. These problems have been diagnosed and confirmed by at least three different service centers including a Chrysler dealership. I generally do not get any warning lamps, messages, or symptoms when the van stalls.

PE25009 - My van has a fault in alignment with this investigation. On long turns with the wheel between 11 and 1 the steering feels heavy then it feels like the system overcorrects. It has done this intermittently for a few months now.

The steering has been sticking causing oversteering at different speeds. This has been getting progressively worse as time has gone on. This is a serious issue as the oversteering to get the car back in a lane is going to cause a serious accident especially at higher rates of speed on the interstates.

While driving, the Pacifica lost all engine power in the middle of an intersection while traveling at 34 mph. All the dash lights blinked and sounded alerts. The car then showed U1267 and U0416 diagnostic codes.

Absolutely, [XXX] — here’s a more natural, human-sounding version of your NHTSA report draft: --- Vehicle Issue Report: Chrysler Pacifica I’m reporting ongoing issues with my Chrysler Pacifica that I believe could be safety-related: Clunking Sound: The vehicle makes a clunking noise when shifting gears. Steering Stickiness: The steering doesn’t always respond smoothly — it occasionally sticks when turning. This makes the car go wider than intended during turns and lane changes, which feels unsafe. I’m concerned they may point to a larger mechanical issue and could affect driver control. I’d appreciate it if NHTSA could look into whether this is part of a known defect or something that needs further investigation. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

As of late of September 2025, our vehicle had approximately 59,000 on the odometer. Around that time, the check engine light turned on. A few days later, white smoke began emitting from the exhaust. On September 27, 2025, the vehicle failed to start entirely. We had the car towed to Brooklyn Chrysler Dodge Jeep Ram (CDJR) for inspection and repair. The dealership performed a diagnostic check and provided the report on October 13, 2025, indicating that the issue was due to a failed head gasket. The repair's cost is $8,711.56.

The engine failed at 104,000 miles despite proper maintenance. The vehicle is used by my wife and three children, and the engine unexpectedly experienced a head gasket failure while on the highway, with no prior warning except for a known issue acknowledged by Chrysler. I am now faced with the costly repair of replacing the engine. As a family relying on this vehicle for daily needs, including school and work commitments, I am disappointed that such issues persist in this model despite widespread reports of similar problems.

Vehicle lost all internal communications while driving. During this incident propulsion was lost, turn signals, hazards, power brakes, power steering, all electronics except speedometer failed. I was unable to put indicators on during this incident outting others at risk. It appears hazards and turn signals are CAN communication which is absolutely insane and a severe design flaw.

I was driving and the van suddenly lost all propulsion. Brakes and steering and dash lights functioned, but there was a red turtle icon and error message about a system failure. The accelerator pedal did nothing at all. I was able to coast off the side of the road to a place to pull over, but that could have been a terrible accident if I lost power like that on I-95 or any other major highway. My husband came and we switch cars (kids, car seats, etc) and he was able to get the van to start after half an hour. It had check engine lights on for things, but the dealer said to bring it in because it was drivable again. Despite brining it in as told, with check engine lights on that they saw, they said they could not reproduce it and couldn't find codes for the check engine light (even though I pulled them from my own OBD2 diagnostic plug tool and took photos of the codes) and eventually said I have to take the car back, despite no cause or resolution. These cars have known faulty battery issues and a large number have been replaced already, but Chrysler isn't authorizing dealers to do that unless they can reliably reproduce the failure. Very frustrating to see Chrysler not go the route of other manufacturers who sourced their batteries from the same plant and ended up proactively replacing them for consumers. While Chrysler's many recalls for the hybrid battery system software have probably made it detect faults earlier to try to prevent fires, they are still known to happen, but now in addition to a fire risk, we also have a car that has a much higher chance of just losing power while driving due to over sensitive battery monitoring, or a plain old faulty battery that just isn't faulty 'enough' for Chrysler to authorize a replacement. So frustrating and dangerous.

Over the past two weeks, on three occasions, the steering "stuck" momentarily (for about a second each time) during low-speed small turns at around 15 mph. Once, a "Service Power Steering" message appeared for approximately 2 seconds, then disappeared; we did not see this message again. Yesterday, the steering locked completely when moving the vehicle from a parking space. We were unable to steer at all while trying to move the vehicle forwards or backwards out of the space at about 5 mph. Turning the vehicle off and on again did not resolve the issue. A "steering wheel and exclamation point" warning light appeared on console. Vehicle was towed. Dealer's service department will investigate.

Problem: Steering wheel sticking in turns. I own a 2018 Chrysler Pacifica. The issue am facing with my car is that the steering wheel is sticking while trying to turn. This issue seems to be happening to so many Chrysler Pacifica owners.

We had the seat fail on one of our middle row seats. It lines up with a dealer service, and we believe the dealer probably broke it while performing other work, but we don't have before/after videos or anything like that to prove it. The issue is that there is a plastic piece that breaks, which means that the seatback no longer locks. This is apparently a common problem in these cars: https://www.pacificaforums.com/threads/broken-passenger-2nd-row-captains-chair-thoughts.54633/ https://www.pacificaforums.com/threads/fix-for-stuck-easy-tilt-2nd-row.47300/ https://www.reddit.com/r/pacificahybrid/comments/1kmsiuj/both_of_my_middle_row_seats_are_defective_they/ The dealer wanted something like $900 to fix it. This is a major safety issue; if the seatback failed during a crash it would mean the other safety systems in the car couldn't do their jobs. We have the broken seat in the garage - we've been driving around without it. I think the pictures in the Pacifica threads above are pretty useful, but if seeing in person would help, happy to meet up or something like that.

The contact owns a 2018 Chrysler Pacifica. The contact stated while driving at undisclosed low speeds, the electric power steering stopped functioning properly after the contact heard an abnormal crunching sound coming from the front end of the vehicle. The contact also stated that while driving at an undisclosed speed, the vehicle briefly jerked and jolted during acceleration as if the transmission was slamming into gear. No warning lights were illuminated. The vehicle was taken to an independent mechanic for regular maintenance service, and the contact was informed that the motor mounts needed to be replaced. The vehicle failures were not diagnosed during regular maintenance service. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 121,000.

After safety recall 73B was performed on my 2018 Chrysler Pacifica Hybrid on 08/25/2025, the vehicle's check engine light illuminated on 09/09/2025. I was inundated with multiple failure lights including; check engine, service electronic throttle control, service hybrid electric vehicle system, blind spot alert, and I felt like I lost power steering. I was unsure if the van was safe to drive, but was able to get it to the dealership. They were able to pull multiple codes. Including the one for the check engine light. They decided that the problem was related to the ABS control module. They replaced it and the van has been fine so far. It seems these error codes are widespread after performing recall 73B. Many other customers are complaining of the same thing. I believe these errors are from the testing to the High Voltage battery, and their 'software fix'. It's not safe to lose your power steering while driving. It's not safe to have multiple error codes continuously going off while operating the car. It's not safe to have a family car that we have been told twice to not park in the garage, charge, or park near a structure. This is their second attempt at 73B, and overall the second fire recall. My van and high voltage battery are definitely available for inspection.

My vehicle went in for recall 73B at the end of August 2025. Every since the recall it has been back to the dealer for multiple check engine lights, service hybrid system, abs system, battery heater fail, blind spot warning temporary unavailable, service shifter(would not go into gear), parking brake, stability control light, partial loss of power steering while driving, service electronic throttle control, and service airbag messages. The van has been to the dealership 4 times for these messages. They have replaced components, tried to find loose wires and connectors, replaced the 12V battery, and other fixes. The van will drive normally for a few weeks, and then they come back. On the latest visit (4th since 73B recall) it's been at the dealership for 31 days and counting. The dealership is waiting on Chrysler to figure out a fix for the van. The vehicle has over 50 stored messages. This recall was supposed to monitor the hybrid battery for early indications for a fire, but according to the original recall all batteries are assumed to have the manufacturing defect that leads to spontaneous fires. This van is unsafe, and we never know when it will work correctly. The van operated normally before the recall software was installed.

Report is related to the probe into a sticking sensation on gradual turns. Particularly when at the 1 and 11 o clock position.

I have written about repeated issues with Auto Start/Stop on this vehicle. Prior dealers have not been able to isolate the problem. Some of the problems seem to mimic a much earlier issue that went to court but did not happen during the timeframe of the class action suit. The prior submission to NHTSA was with this tracking number: 11681967 . I am now submitting repair information that aligns with my complaint of the Auto/Start stop on this vehicle. I am submitting this because it helps to support my earlier submission. Thank you

The steering sticks when when turning in curve left and right turns causing me to sometimes over correct.

Steering experiences sticking during gradual curves in the road. It requires some effort to return the steering wheel from the stuck position and I’m worried that it won’t someday and cause a collision.

Often when making a gradual turn such as exiting an interstate onto the off ramp, the steering wheel will stick/lock at the 3 o clock position. This requires considerable force to return the wheel to the 12 o clock and straight position. I took it into the dealership and they found nothing wrong but it seems like an issue with the steering rack. I've heard numerous reports of others encountering this as well and I want it to be known this is a common issue. There is no grinding, scraping or noise indicating something is broken but seems to be a manufacturing defect. It is extremely dangerous and can sometimes be rather difficult to correct the wheel.

Back up camera freezes or shuts off almost causing collision

Blown Head Gasket (Cylinder 3 Misfire) After having 2018 Chrysler Pacifica Touring L serviced at Chrysler Dealership, technicians found small leak coming from Oil/Coolant Filter housing unit. Part was replaced and few days later vehicle had a misfire and had flashing Check Engine Light (CEL). Car was towed to dealership, technicians said code seen was P0303 (Cylinder 3 Misfire). Tech, replaced Ignition coil for cylinder 3 and cleared codes. Two days later on start up, P0303 (cylinder 3 misfire) came back with CEL. Tech cleared codes and could not re-create CEL again. Two days later P0303 came back. Technicians performed more diagnostics and confirmed blown head gasket. This seems to be a very prominent issue with 2017-2018 Pacificas, more notably Cylinders 1, 3, & 5. The catalytic converter sits above the firewall cylinder bank and possibly is causing this possible engine failure due to excessive heat and poor heat dissipation capability over time. If not caught quickly, coolant can leak into cylinder affected and then overheat engine causing irreversible damage. This situation can also create a very hazardous situation if driving into speeding traffic from a turn and engine misfires, my vehicle could be rear ended if acceleration does not happen quickly enough.

Vehicle will start but the shifter will work. It threw a check engine light and check hybrid system code. You cannot get the vehicle out of gear and the shifter will not light up. After shutting the vehicle off and on 3 times it erased and acted like it never happened. This is the third time it has happened. What’s bad you can drive somewhere and be stuck there for hours not knowing if you need a tow or it’s going to reset again. Don’t know if something my happen while driving as well.

My van completely shut off, and all lights on the gear shifter stopped working. Yes, it is available for inspection until the gear shifter is replaced, as recommended by the dealership. The van lost power just as I lifted my foot off the brake to proceed into an intersection. This sudden shutdown created a traffic backup behind me and could have put me and others in danger had I entered the intersection. The issue has only occurred once for my husband while driving but has not been officially reproduced or confirmed by a dealer or service center. Yes. I took the van to the dealer, who suggested replacing the battery and the shifter. I replaced the battery and ordered the shifter, but the second failure occurred after the new battery was installed. In addition, I’ve noticed a continuous clicking sound coming from the van after it is turned off, which does not stop for approximately 5 minutes. There were no warning lights or messages before the failure. After the van shut down, the “start assist” light came on, and it did not turn off until about four days after the battery replacement.

The steering periodicall locks up. This doesn't happen offten and only lasts a second or two but at high speeds does give a scare to the driver. Also when turning the steering in a tight turn like in a parking lot, the steering jerks/wabbles.

Electrical adaptive, cruise control, forward collision warning, and shifter all malfunctioned. It is available for inspection. There was failure to accelerate at an intersection which almost caused vehicle to be rear ended. The error codes have been pulled and shown by O’Reillys auto parts. The vehicle is pending inspection by an independent mechanic. The adaptive cruise control the Ford collision, warning and service shifter warning lamps all appeared shortly before this problem occurred.

When beginning to move from a stop, the transmission occasionally does not engage for a few seconds and allows the vehicle to drift unexpectedly before it slips in gear and moves. Also, occasionally when shifting gears once moving, the transmission “pops” into gear, which feels as if I have been rear-ended. This has been happening for a few years and has been at the dealership 5 or so times with no resolution.

When negotiating some turns the steering wheel "sticks" and resists turning back out of the turn a little. It makes slight corrections jerky.

2018 Chrysler Pacifica, 3.6L V6, approx. 66,476 miles. The vehicle began losing coolant with no visible external leaks. When cold, opening the coolant reservoir cap releases a strong hiss of pressure and coolant flows back into the tank. The check engine light appeared, first showing a cylinder misfire (resolved after spark plug replacement), then later a slow EGR leak code. Over the next several weeks, the coolant level continued dropping and the reservoir remained pressurized even when cold. Vehicle was inspected by Waxahachie Dodge Chrysler Jeep (RO #490099, Sept 2025). Technician performed a combustion gas test and confirmed exhaust gases are present in the coolant system. No external leaks were found. Diagnosis: failed head gasket allowing combustion gases into the cooling system and coolant to burn in cylinders. The technician stated overheating or warpage may have opened a path at the head gasket but found no external signs of overheating. This condition poses a safety risk—coolant loss and trapped pressure can cause sudden overheating, engine stall, or hydrolock while driving, potentially leading to loss of power or a crash hazard. The issue was confirmed by a Chrysler dealer and documented in the repair order. The vehicle remains available for inspection. Prior to failure, symptoms included the check engine light, rough running, and repeated coolant loss. There were no visible leaks or overheating messages. Manufacturer was contacted but declined assistance; dealer verified diagnosis and estimate for repair (~$7,800).

I am experiencing the issue that was widely reported in the news on 9/8/2025. The steering starts to stick when the wheels are turned on gentle curved. This happens after about 1 hour of driving, and it most likely to happen between 45mph-65mph. Car has approximately 58,0000 miles on the odometer. This is a massive safety issue, a driver should not have to fight the steering wheel to maintain control of the car. Problem has not bee reproduced by mechanic or dealer. No warning lights come on during the event.

While slowing to a stop at a traffic light, the engine stalled unexpectedly. The start/stop system did not restart the engine when I released the brake pedal. Accessories (radio, lights, etc.) remained powered, but I could not shift the vehicle into neutral. After approximately 20 minutes, I was able to restart the engine; however, the transmission remained unresponsive and the engine could not be shut off using the ignition button. I was unable to shift to neutral or turn the steering wheel. Message on dash indicated shifter module required service, and indicated that the vehicle was not in park when attempting to turn off vehicle. The vehicle was only turned off by disconnecting the 12-volt battery. The vehicle was towed to a Chrysler dealership and diagnostics completed, showing error codes with the shift module. They were unable to recreate the problem and advised replacing the shift module. When inquiring about recall V53, the dealership service department indicated that this recall had been repaired on the vehicle in 2020. These symptoms match those described in Chrysler Recall V53 (NHTSA Campaign 19V-348) for 2017–2019 Chrysler Pacifica vehicles equipped with start/stop systems, which involves a loose battery ground connection. My VIN is not currently listed in the recall as it was reportedly corrected in 2020, but the issue created a hazardous situation by stalling in traffic, disabling shifting, and preventing engine shutdown. This could have resulted in a crash if traffic conditions were different. Please investigate whether additional 2018 Chrysler Pacifica vehicles not currently included in Recall V53 should be covered or if this is a recurring safety issue with the engine start-stop (ESS) on 2017-2019 Chrysler Pacifica vehicles.

Check engine light came on the day after the automatic start/stop light came on. Engine code read cylinder 4 misfire. We switched all the spark plugs and changed the cylinder 4. A couple days later check engine light came back on brought the vechile into Bergstrum. They put in a name brand cylinder 4 plug and spark plug, 2 weeks later the light came back on, same exact issue. They are now claiming it’s an engine issue potentially. Sounds like this is a BIG problem for 2018 Chrysler pacificas.

This vehicle experience is intermittent installing or fails to restart after the engine shut down I verified there are currently no open recalls and I believe this may be related to a known PCM or emissions related issue

Quirk Chrysler Dodge Jeep RAM Of Dorchester refused to perform Recall 73B/24V-536 on my restricted-title Pacifica (reconstructed), citing Chrysler policy. That policy doesn’t exist in the recall bulletin. I need the BPCM software update and any necessary battery replacement under the recall.

The lock actuator on the sliding door does not function correctly. The same exact part in the same designed car (Dodge Caravan) has a settlement for this. This should also apply to the 2018 Pacifica. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The steering wheel sticks forcing you to almost have to jerk the wheel to stay in your lane. Seems to be highway only. Very dangerous This was not a one time occurrence. Happens every time the car is driven on the highway

I have been experiencing a brake surge when I come to a stop, it has been a few weeks now (or maybe months). It feels like the regenerative braking is disengaging and the friction brakes are not engaging immediately. I am concerned this is a brake handoff issue and a major safety problem.

Auto start/stop alarm displays in dash. Have taken it to two different dealerships and they say they can find no problem. They car hesitates when stepping on the gas. There have been incidences when the car stalls all together. We have now noticed that the issue is more prominent when the weather temperature is hot like over 90 degrees but especially if the temperature is over 100 degrees. Also just recently within past few weeks the car will stall but keeps going though you cannot accelerate, however, you do not lose steering ability. You have to pull off the road and shut the car down and restart it and then all components work properly. Again this is happening when weather temperatures run high. This has been an issue last year as well. I called Chrysler and got a Star Case # 91330213 but then we stopped having the problem. Most likely because it got cooler but we are having issues again this year now. What is interesting is that the dealerships say they cannot find any code being set off because at times the auto start/stop alarm will reset and then they say they do not see an issue. Yet we know there has been an issue & continues to be an issue.

Head gasket failure at a 107,000 miles.

The contact owns a 2018 Chrysler Pacifica. The contact stated that while driving at various speeds and attempting to turn the steering wheel slightly to the left or the right, the steering wheel was sticking, causing the contact to use added force to straighten the steering wheel. There were no warning lights illuminated. The vehicle was taken to be diagnosed, and the contact was informed that the electronic steering system had failed. The contact was informed that the steering system needed to be repaired, and the rack and pinion needed to be replaced. The vehicle had not been repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 120,500.

The hybrid battery system is malfunctioning. I am not at risk. I am repeatedly getting U0412 error code, indicating a problem with voltage in the hybrid battery system. It only happens intermittedly. I have taken it into the dealer when the check engine light is not on (unfortunately), and they did not find any issue. One time while driving at highway speed, I did get an immediate red message saying "check hybrid system". It went away with the check engine light remaining on for about an hour. This has occurred after (and I think because of) the 73B recall.

The contact owns a 2018 Chrysler Pacifica. The contact stated that while operating the vehicle, the check engine warning light remained illuminated. The contact stated that there was no coolant in the coolant reservoir. The vehicle was taken to the local mechanic, who indicated that a coolant pressure test was needed. The vehicle was later taken to the local dealer, who diagnosed that the front and rear head gaskets needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 51,000.

while driving on I40 east of Ashville, the power steering became sluggish. like turning in molasses. I had to manhandle the steering wheel to complete the turns (at 70 mpg). My wife also drove on I40 and felt the same thing I was feeling. The next 3 days it did not do it again, I was driving in town. Later I felt it while going on a curve at about 62 mph. This also happened to be going up an incline. Earlier on i40 it did not mapper if going up hill or down hill.

The contact owns a 2018 Chrysler Pacifica. The contact stated that while driving at speeds above 30 MPH, after making a slight turn to the right, the steering wheel became sticky, and added force was required to turn the steering wheel back to center. The vehicle was taken to the local dealer, who diagnosed that the steering rack was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed of the NHTSA Action Number: PE25009 (STEERING). The contact indicated that the vehicle had experienced the failure listed in the investigation. The failure mileage was 114,000.

Component/system failed: Electric Power Steering (EPS). The system intermittently fails during normal driving, showing a "Service Power Steering" warning. Diagnostic codes include U113E (lost comm w/ EPS), C2217 (SAS not calibrated), C2210 (EPS internal fault), P058C (low voltage), and P1009 (hybrid module MIL request). The issue began immediately after a Chrysler recall service where the main charging unit was replaced. Vehicle is available for inspection. Safety risk: Loss of steering assist creates a serious hazard, especially during turns or at low speeds. The steering becomes extremely heavy without warning, increasing the risk of collision or inability to maneuver safely in traffic or parking situations. Dealer confirmation: Yes. A Chrysler dealer confirmed the EPS fault and quoted $5,500 to replace the entire steering rack. No electrical diagnostics were completed, despite the issue starting after recent electrical recall work. Inspections by others: The dealer has inspected the vehicle. Chrysler corporate has been contacted but has not yet resolved the issue. No inspections by police or insurance. Warning signs: The issue started right after the dealership performed recall work. “Service Power Steering” message appears, and diagnostic trouble codes are present. The error is intermittent and can clear after restarting, only to return later.

The contact owns a 2018 Chrysler Pacifica. The contact stated that while driving at various speeds and turning, the steering wheel was sticky and failed to return to center automatically. There was no warning light illuminated. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact related the failure to NHTSA Action Number: PE25009 (Steering). The manufacturer was not notified of the failure. The failure mileage was approximately 127,000.

While driving at a steady 65 mph, I suddenly lost power steering, which severely reduced my ability to steer the vehicle. I was able to safely brake and pull over. After turning the car off for a few minutes, steering function returned to normal. A few hours later, during a second drive at approximately 35 mph, I experienced the same issue again while turning onto my street. The steering wheel became extremely difficult to turn and required significant effort with both hands to maneuver the vehicle into the driveway. This sudden loss of steering control posed a serious safety risk-not only to myself, but also to other drivers on the road-and could have easily resulted in an accident. No warning lights or dashboard alerts were displayed at any point. The vehicle was towed from my home to the dealership. Upon inspection, the issue was reproduced, and it was confirmed that the power steering system had failed and required repair, along with related components. All necessary repairs were completed and paid for out of pocket.