NHTSA Owner Complaint Log
This page lists owner-reported complaints filed with NHTSA for the 2008 Honda CR-V. Complaints are unverified consumer reports submitted to NHTSA and do not by themselves prove a defect or defect rate.
Odometer Fraud. The contact purchased a 2008 Honda CR-V. The contact discovered that there was a mileage discrepancy after the purchase. The vehicle was a private sale. At the time of the purchase, the mileage was 137,000. It was later discovered upon registering the vehicle with the DMV that the mileage was 255,000.
Hello, I have a recall for the corrosion on my Honda CRV 2008, American Honda already has everything on file from the dealer ship I took to get it inspected and is been a whole month and American Honda hasn’t reached out to me. I have been asking American Honda if I could get a loaner car or rental as the service manager at the dealership has said he cannot provide a rental until American Honda authorized since obviously some one has to pay for it. And I’m just reaching out if you guys could help me anyway to help me get this sorted out, dealership has already told me the car is un repairable at this point due to the bad corrosion and American Honda has acknowledged that and said someone from the median department or something like that was gonna reach out to me that was 2 weeks ago and I have reached out a week ago and they said someone would reach out and I have not received anything as I have told them, I really need a car since I recently had my baby and you know I need to come to work and go back home. Please if you guys can help me
My light start turn on and off in some times and this start happens 3 days ago
The contact owns a 2008 Honda CR-V. The contact stated that while the vehicle was parked, the front passenger's door failed to latch as intended. In addition, the front passenger's door had independently unlatched. The vehicle was taken to the dealer where it was diagnosed with a failed door lock actuator. The contact was informed that the front passenger's side door actuator needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the issue, and a case was filed. The contact referenced an unknown Technical Service Bulletin with a similar failure; however, the contact was informed that the TSB had expired. The failure mileage was approximately 53,000.
This is a complaint in reference to a current recall for the rear rust and corrosion issues on Honda CRvs, Part 573 Safety Recall Report 23V-228. I brought my vehicle to Matt Burne Honda on January 7 2025 for this recall and they "inspected" and passed the vehicle, installed the brace, and said all was well as they handed me the keys. In early March I took the car in for its state inspection and it failed due to all of the rust/corrosion/frame rot on the rear of this vehicle. When I called Matt Burne to find out why they installed the brace on this vehicle with all that rust, and why they never even bothered to mention the rust to me, they said that for the recall to pass all they needed to do was remove the bolt for the trailing arm and that all the rust didn't matter, and whether or not it could pass a state inspection didn't matter. This, put me and my family at risk. The rust and corrosion is severe. My family and I have been driving in it thinking it was all okay since the recall was completed. Yet they never thought to mention it. Isn't this recall in reference to rust and corrosion on the rear frame? Yes, I understand it involves the trailing arm, but wasn't there a punch test and a frame inspection that was supposed to be a part of this? How is it that the frame can rot away and practically disintegrate and yet that doesn't matter? After a month of trying to reach Honda, they finally told me I needed to take it to a Honda dealer because the 2 inspection centers I had taken it to weren't good enough. I wound up taking to to Motorworld Honda for an "inspection" and all they did was look at the installed brace and say everything was good, even though that at this point they were now unable to put the car on the lift since that spot on the frame has rusted away. In March it was able to be put on the lift? What happened since? And how is this acceptable as far as this recall is concerned? They put my life and the lives of my family at risk as well as others.
Both automatic door locks are malfunctioning on the passenger door side. They will not stay unlocked with the vehicle is unlocked. Daughter was choking in backseat & the door would not open unless I pushed the unlocked button and opened the door at the same time.
*(#1)2024 COMPLETELY TURND OFF DEAD STOPEF IN THE MIDDLE FREEWAY HIGHWAY PATROL HAD TO TOW IT AWAY LASY YEAR COST ME $900+ **** AGAIN NOW ALMOST PASSED OUT NO AIR BAG TO SAFE ME***** (#2) 3/6/2025 CAR COMPLETLY CRASHED ,INJURED ,I WAS TAKEN BY 911 TO HOSPITAL. ** BAD AIR BAG DID NOT CAME OUT OR NEVER WORKED TO PROTECTED ME***, I GOT HIT MY CHEST SO BAD , THOGHT I WAS GOING TO DIE THST MOMENT. CURRENTLY I RENTED A CAR TO PAY IT DAYLY $$$$ GO TO DOCTOR FROM MY OWN POCKET.[I CAN AFFORD] SINCE I LOST DO NOT KNOW HOW LONG WILL TAKE TO BE REPLACED MY 2008 HONA CRV ,WITH SAFER VEHICLE. I NEED TO HAVE TRANSPORTATION I SHOLDN'T CHARGED FOR RENTING A CAR AND GET HELP WITH FREE RENT TRANSPORTATION SOONER UNTILL SOMEONE RESOLVE THIS DADLY ISSUE. THANK GODI'M ALIVE
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) and the vehicle was repaired under the recall; however, the contact was informed that the dealer had observed a 3X8 inch hole located 2 inches away from where the support brace was installed. The contact stated that despite the hole, the dealer determined that the vehicle was safe to drive, and the vehicle passed inspection. The contact believed that the recall repair failed to adequately address the safety concerns of the recall, potentially leaving the vehicle with a rear trailing arm that could still detached in the future. The manufacturer was made aware of the failure and a case was filed regarding a possible buyback; however, the request was denied due to the age of the vehicle. The failure mileage was 211,600.
The contact’s son owns a 2008 Honda CR-V. The contact stated that while his son was driving 45 MPH, the vehicle aggressively veered over to the right side of the road. The driver inspected the vehicle and noticed that the rear axle had detached from the frame. The driver was able to coast to the side of the road. The vehicle was towed to the dealer who was unable to fix the vehicle under NHTSA Campaign Number: 23V228000 (Structure); because parts were not available, and there were additional damages that needed to be repaired. The manufacturer was made aware of the failure and was working with the dealer to have the vehicle inspected. The failure mileage was unknown. Parts distribution disconnect.
Door actuators ( Front passenger side and Back driver side) does not work. It bothers me by locking and unlocking.
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was contacted. The dealer informed the contact that there was an extreme amount of rust to the frame of the vehicle. The bolts failed to release due to the extreme rust. The vehicle was not able to be placed on the lift due to frame rust. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The approximate failure mileage was 133,267. Parts distribution disconnect.
Understand my car is old but I also understand that there was a class action lawsuit I was not informed about regarding the door actuators the door locks on my vehicle I paid $300 plus to replace the front door actuator and now my back door driver side and back door passenger side door actuators are extremely loud and it is difficult to unlock the door if you're on the inside of the vehicle trying to get out it freezes the door locks that's very dangerous I know my car is old but Honda should still have to replace them considering they agreed to replace all four door actuators back in 2015 but I was not informed of that.
Two actuator for the doors were said to be replaced by the previous owner in 2015. However, all four of my actuators are not working. Sometimes, it unlocks by itself when driving and I have had issues at times when I am not able to unlock the door at all. This poses safety risk to not being able to get out at times from both inside and outside.
The contact owns a 2008 Honda CR-V. The contact stated that the rear passenger's side door was making locking sounds unintendedly and had failed to unlock as needed. The vehicle was taken to an independent mechanic, where the door actuator was replaced, and the door was repaired. Additionally, the contact stated that front passenger's side door and the tailgate had failed to unlock as needed. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and informed the contact that the vehicle was not covered under an unknown recall because the recall had expired. The failure mileage was approximately 68,000.
When i unlock the key fob and put hand break to park the driver side door makes a loud squeeky sound.
The contact owns a 2008 Honda CR-V. The contact stated that upon taking the vehicle into an independent mechanic for service, the contact was made aware that the rear trailing arm had severe frame corrosion, potentially compromising the vehicle safety. The vehicle was taken to the dealer, who confirmed the diagnosis and advised the contact that the vehicle could not be repaired. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 23V228000 (Structure) however, the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 150,000.
Hello I’m [XXX] and own a 2008 Honda CRV that runs fine. VIN [XXX] , but previous owner never went to the recall and I bought the car in 2014 and recently, during a brake job, I first became aware of the problem when my mechanic alerted me to the recall situation and the rusting out that was putting drivers in a very dangerous situation. My car failed the recall because of the rust causing the degradation of the rear suspension trailing arm, and now I'm left with a car not fit to drive? and I would be liable for whatever happens but I was never offered a solution to buy the car back something to help and I cannot be without one to get to Dr’s or buy food live rural I have no choice living alone at [XXX] need a car. So a question, why am I the problem? when, in the first place, the car was dangerous from the manufacturer to the rusting out situation which was actually life threatening, lose steering, the wheel could collapse or the frame itself, and again, never offered any help at all some compensation, nothing? Just drive it home with the burden of the liability etc. I’m on a Fixed income of only $800 a month how am I to survive living rural without a car at my age? Please, I need some help. Why am I being punished when the design itself, as I said, created the dangerous problem and just that's it? Appreciate help from someone. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Evidence of corrosion on the rear trailing arms as described in the recent salt belt recall of 07-11 Honda CRV’s. Petition to expand the monitoring and repair scope of this recall to include the Appalachian regions of North Carolina and Tennessee as the use of road salt is also prevalent in these areas.
Vehicle door locks acting up off & on for several years. Sometimes not unlocking needing to insert key to unlock, other times passenger door not locking when using fob and doors locking & unlocking while driving. Now most recently cannot open drivers door from inside. It can be opened from the outside. This is very dangerous if you needed to get out of car quickly, not to mention the inconvenience of crawling over the center console to get out of passenger door. I am [XXX] and will never buy another Honda as I’ve read about the problems with this. Too bad because I really like my crv. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2008 Honda CR-V. The contact stated while driving at an undisclosed speed, the vehicle briefly lost motive power before returning to normal functionality. After restarting the vehicle, the vehicle returned to normal functionality, but the failure became a regular occurrence. The check engine warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related it to NHTSA Campaign Number: 11V395000 (Power Train), but the VIN was not included. The failure mileage was 190,000
Door locks began opening and closing on their own while I was driving. I have replaced battery twice since this began. The auto repair place and AAA were unable to locate a cause for the electrical problem. The car will not stay locked. I was robbed of my personal property while it was parked. It is not really safe to drive since I cannot secure myself in it.
When locking the door, there is a loud noise. I was told the lock actuator is bad and needs to be replaced (driver rear). I purchased this vehicle in October 2022 and the warranty is no longer valid. Prior to, the passenger front lock actuator had to be replaced. The vehicle is available to be inspected upon request
Auto door locking system attempts to lock all four doors every time the vehicle drops below 10 miles per hour and then goes above 10 mph. All four doors can be manually locked and show they are locked when the motion auto lock system thinks one or more are not locked and attempts to lock after 10 miles per hour. This continues for every trip.
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
On 08/09/23 at 1108 hours, I called Langdale Honda in Valdosta, GA. I told them of the current recall on my vehicle. It was verified via VIN, and then I was discouraged from bringing in the vehicle. I was told that the recall applied to northern cars that suffered from salt and snow exposure, and that my vehicle should be OK. It clearly states in the recall notice that mud can also be a factor. I reminded the associate of that. I also reminded the associate of Federal Law. Thereafter, he said that I could bring the vehicle in if I desired; however, I was concerned because I bought my vehicle used. I don't know its history, and don't know from where it originally came. I did not make an appointment with Langdale due to mistrust.
VEHICLE IS ACCELERATING ON ITS OWN
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) and the vehicle was taken to the dealer for the recall repair; however, the dealer informed the contact that they could not install a support brace on the vehicle because unknown bolts failed to loosen for the repair. The dealer had not provided any additional information regarding the failure. The contact was informed that photos had been sent to the manufacturer and the dealer was awaiting a response. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and informed the contact that an assessment and follow up would be made. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2008 Honda CR-V. The contact stated that while driving at approximately 45 MPH, the accelerator pedal was depressed; however, the vehicle was slow to respond. The vehicle lost motive power and shut off. The contact stated that after five minutes, the vehicle was restarted; however, while driving at an undisclosed speed the vehicle inadvertently shut off. The contact was eventually able to restart the vehicle, and the vehicle operated as designed. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 180,290.
Driver door actuator started jamming late July. Door would only look after pressing the lock button from the passenger side. It eventually stopped locking that way and would only lock after hitting the lock button 8+ times on the driver side. Yes it is available for inspection upon request. My own safety is put at risk due to this issue because my doors are unable to lock. As a young woman, who doesn't have access to a garage and sometimes doesn't get home till late, having doors that are completely unable to lock due to a known system issue from Honda makes me uneasy. Yes, the problem has been confirmed by an independent service center. No the vehicle has not been inspected by the manufacturer, etc... No, the car provided no warning lamps, messages or any other symptoms of the issue. Issues first appeared in late July and have drastically gotten worse since then.
Rear right passenger lock actuator failing to unlock randomly, sometimes locks only partially.
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the recall repair could not be completed due to the extent of corrosion on the vehicle. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair as the recall notice was received over a year ago and the inspection was completed 8 months ago. Also, as per the recall notification, depending on the extent of any corrosion damage, Honda might offer to repurchase the vehicle. The dealer was contacted and confirmed that the recall repair could not be completed due to the extensive corrosion. The manufacturer was contacted, and the contact stated no offer was made, however a case was opened. Parts distribution disconnect.
The contact owns a 2008 Honda CR-V. The contact stated that the vehicle was taken to the dealer for the recall repair of NHTSA Campaign Number: 23V228000 (Structure) and an unknown door latch recall; however, while driving after the vehicle was returned, the contact became that the doors were no longer closing securely, and the vehicle failed to respond immediately while depressing the brake pedal. There was no warning light illuminated. Additionally, the contact stated that the dealer had stated in the recall repair work order that the recall repair of NHTSA Campaign Number: 23V228000 (Structure) could not be completed on the vehicle due to severe frame corrosion and that the sub frame needed to be replaced; however, the dealer installed support braces on the vehicle and marked the recall as Complete. The vehicle was taken to an independent mechanic, where it was diagnosed that the brake caliper had seized. The independent mechanic notified the contact that the vehicle was unsafe to drive. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 402,685.
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) and the vehicle was taken to the dealer for the recall repair. However, the dealer fractured the rear trailing arm bolts while inspecting the vehicle and informed the contact that they could not complete the recall repair due to corrosion. The dealer advised the contact that the manufacturer was notified of the issue, and the dealer was awaiting a decision from the manufacturer whether to buy back the vehicle. The contact stated that the vehicle was undrivable and he had not received assistance from the manufacturer or the dealer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and a case was opened. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) and requested to be removed from the recall distribution list. The local dealer was contacted. The manufacturer was not contacted.
Door locks they lock and unlock by themselves and make a noise when locking. Also paint on car doors and back hood paling off car you see medal.
I thought I needed new brakes put on because my brakes sounded like they were grinding and they were going to the floor so I had new brake pads out on but my Mechanic said the brake pads were fine he replaced them anyways. I went to have an oil change and a different mechanic said that I needed and alignment but my entire back end frame was rusted and corroded. He said if I got an alignment my back end would collapse because the suspension is bad. When I go to brake my brakes go to the floor so I'm guessing thats from the suspension being messed up. He said it's not safe to drive
The rear frame of my CRV has corroded and deteriorated. The rear trailing arm is at risk of falling off and could cause a loss of vehicle control, increasing the risk of a crash. The recall paperwork I received from American Honda Motor Co. Inc. states, “Your Honda dealer will inspect the rear frame for corrosion. Depending on the extent of corrosion, the dealer may attach a support brace to the rear frame and/or repair the rear frame, for FREE. If the rear frame cannot be repaired, Honda may offer to repurchase the vehicle from you. If you paid out of pocket to have these specific recall repairs performed on your vehicle, you may be eligible for reimbursement.” I took my vehicle to Honda North for the repair. They attached the support brace, yet told me my vehicle is still unsafe to drive and refused to pass my vehicle for the required PA state inspection. I believe they need to move to the next step on the recall (repair of the rear frame) since the addition of the support brace did nothing to correct the safety issue on my vehicle. I took my vehicle to get two second opinions and both stated the vehicle is unsafe to drive due to the rear frame corrosion. I do not understand how Honda can put out a recall specific to the rear frame, then refuse to make the appropriate corrections so that the vehicle is safe. Why bother attaching the support brace if it does nothing to correct the reason for Honda’s recall? I filed a complaint with American Honda, but I have not heard back from them in 3 1/2 weeks although I call daily. I was quoted $3000 for these repairs by an independent body shop.
This year, a 2008 Honda CRV encountered an issue wherein one of the bolts on the rear trailing arm, a crucial component of the vehicle's suspension system, became lodged and partially snapped off within the rear frame of the car. This occurrence had the potential to adversely affect the vehicle's stability and handling. Coinciding with, Honda issued a recall notice for select CRVs this year. The recall was prompted by concerns about the potential development of rust and corrosion within the rear frame of these vehicles. The recall's primary objective was to address potential structural complications, such as rust-related issues with bolts and the rear suspension, which had the potential to compromise the overall safety and integrity of the CRVs. Upon inspecting the affected 2008 Honda CRV, a Honda dealership concluded that the issue involving the lodged and snapped bolt in the rear trailing arm was not directly attributable to the rust and corrosion covered by the recall notice. Consequently, Honda clarified that they could not assume responsibility for this specific problem, and the scope of the recall did not extend to cover the situation of a snapped bolt within the rear frame. In response to the situation and to mitigate potential risks, the Honda dealership proactively implemented measures. They reinforced both sides of the rear trailing arm by securely attaching a sub-bracket to the vehicle's frame. This additional structural support was designed to ensure the proper attachment and functionality of the rear trailing arm. However, since Honda's assessment indicated that the issue of the lodged and snapped bolt was distinct from the rust and corrosion specified in the recall, the vehicle's servicing was only partially addressed, leaving it in an unsafe state. The dealership recommended a nearby body shop sponsored by Honda. This body shop conveyed that the issue should be raised with Honda, as they believed the problems were interconnected.
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
A/C compressor in 2007-2011 Honda CR-V has a known defect in the A/C compressor clutch. The clutch component of the compressor includes the pulley which turns the compressor motor. When the clutch fails, the compressor motor seizes up and stops the pulley from turning. The pulley on the compressor is driven by one serpentine belt on a tensioner which turns the alternator, the power steering motor, the crankshaft, the water pump, and the A/C compressor. When the A/C compressor seizes up, the belt will snap in two every time because the A/C pulley will not turn. The car will not be operable unless the A/C compressor is replaced. To replace the A/C compressor, the refrigerant must be vacuumed out, the condenser and desiccant replaced, the compressor replaced, the system recharged, and a new belt put on. This costs about $2500 at Honda or at another shop around $1700. Honda refused to fix the clutch when I took my car in after discovering the A/C was not working. I have replaced the compressor in this vehicle twice already, and now it needs a third replacement. It is a safety issue because the belt will break while driving causing power steering to go out, possibly causing a crash, the battery will not charge, leaving you stranded, the water pump will not function causing your engine to overheat, and possibly causing a blown head gasket or worse. This situation has occurred twice already but I’m reporting the latest one.
The contact owns a 2008 Honda CR-V. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 23V228000 (Structure). The contact stated that while driving at an undisclosed speed, the vehicle made an abnormal sound. The contact self-inspected the vehicle and noticed that the power steering fluid level was low. The contact filled the power steering fluid reservoir; however, two days later, the failure recurred. The vehicle was taken to the dealer, where the passenger’s side front ball joints were replaced, the power steering kit was installed, and the drive belt was replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 135,500.
Door lock actuator failed.
Several of the door locks on our 2008 CRV will automatically unlock after locking the car when parked making it an easy target for theft. And when the car is running and in Park, several of the door locks will not unlock making it extremely difficult to let someone into the car.
On October 9, 2022, I filed a complaint with NHTSA regarding this vehicle due to excessive and extreme rear frame corrosion. On May 6, 2023, my son was driving this vehicle and was involved in an incident while the vehicle was in motion. The rear subframe separated from the vehicle on the driver side. My son lost control of the vehicle. Fortunately, my son was able to avoid a direct collision with oncoming traffic. On May 15, 2023, the vehicle was towed to Victory Honda in Monroe, Michigan. The vehicle was inspected, and we were assigned a case number (#13814983). We were promised a loaner vehicle (which has never been made available). As a result, my son had to resign his position at work because he lost his mode of transportation. I have called American Honda on a weekly basis requesting an update. I've been told our case is almost completed. We have been waiting for more than 4 months for the buyback as promised. We were told we would be getting $7,900 for the CR-V, plus out of pocket costs paid for a rental car on two occasions and payment for recent mechanical improvements. Honda USA has failed to resolve this manner in a reasonable and timely manner. 100+ days is not timely. We have lost income due to the loss of use of this vehicle. We have not been provided the loaner vehicle as promised. Please escalate our complaint. This is the second time this matter is being reported to the NHTSA. Please note, this is more serious now since my son was driving the vehicle when the subframe separated. He could have been killed or badly injured.
Vehicle rear frame broke while driving and had towed to Brown Honda in Toledo Ohio to look at it. At the same time Honda recall 23V228 came out from the NHTSA where Honda acknowledged this rear frame issue and under that recall the dealer was required to either repair the vehicle or purchase it from the owner. Brown Honda verbally said the vehicle was non-repair able and they weren't going to do anything else because it was "too old." We called Honda corporate and they refused to do anything until Brown put the "unrepairable notice" in the system. We called Brown Honda again and contacted them a 3rd time via email and each time they have refused to do anything else or even respond, but have told us again it isn't repairable and too old. Brown then told Honda corporate that they did not even have the vehicle., so we took a picture of it sitting in the Brown lot with the dealership sign and sent it to Honda. Honda contacted Brown again then came back to us and told us they couldn't force Brown to do anything and at this point Brown was refusing to take it any further. Honda corporate then told us they were not going to do anything further either since Brown would not put the ticket in the system saying it was unrepairable, then told us they were going to close our case #[XXX] in Honda's system. Their final suggestion (Honda corporate) was to try towing it to a different dealer and see if they would do something. So at this point, Honda and their dealers are failing to abide by the recall notice and should be subject to fines. They are costing us more money by having us now try having it towed to other dealerships until I guess we find one that will follow the recall agreement. NOTE: [XXX] (owner of vehicle) is fighting cancer and I [XXX] am helping her with this, I am her son-in-law, I will attach her mailing address to the complaint but my phone # and email address. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
The contact owns a 2008 Honda CR-V. The contact stated she locked her child and dog inside the vehicle and was unable to open any doors with the key. The contact stated she sought roadside assistance to open the door. The contact took the vehicle to the local dealer, where it was diagnosed with needing the door lock actuator to be replaced. The vehicle was not repaired. The manufacturer had been informed of the failure. The failure mileage was unknown.
The contact owns a 2008 Honda CR-V. The contact stated that after starting the vehicle and driving, within minutes the front driver’s side door erroneously unlocked. The cause of the failure was not yet determined. The vehicle was taken to the local mechanic who was unable to determine the cause of the failure. The manufacturer was notified of the failure. The local dealer was not contacted. The failure mileage was 80,000.
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA Campaign Number: 23V228000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2008 Honda CR-V. The contact stated that while having an inspection performed on the vehicle, she was informed that the rear sub frame was corroded and had holes. The vehicle was taken to the local dealer where the vehicle was repaired under NHTSA Campaign Number: 23V228000 (Structure). The contact stated that the rear support brace was added. The vehicle was repaired but the mechanic informed the contact that the vehicle was not drivable. The manufacturer was contacted but provided no additional assistance. The failure mileage was approximately 128,000.
My vehicle had the recall of the door locks completed but it has started the same problems again. Doors locking and unlocking at random while driving. Door unlocking once I have got out of the vehicle at a store and I have no idea for how long. Front and Back doors on the driver side is now making a grinding and loud popping noise when locking/unlocking the doors. The back gate tells me it is ajar but is not. The doors may or may not let you out of the car once you have arrived at your destination and placed the vehicle in park. The unlock button does not seem to help this problem. You must move the gear shifter back and forth and finally you can exit the vehicle. SAFETY ISSUE. Another recall needs to done for this issue.
Data synced from NHTSA on May 4, 2026