NHTSA Owner Complaint Log
This page lists owner-reported complaints filed with NHTSA for the 2018 Mazda Mazda3. Complaints are unverified consumer reports submitted to NHTSA and do not by themselves prove a defect or defect rate.
While I was driving on the highway, I went to use my front wipers and there was no response when trying to active them. The rear wiper, front and rear washer fluid sprayers all worked. No warning lights or other signs of failure were present. I took the car to a local repair shop and they diagnosed it as a bad Body Control Module. Once the module was replaced and reprogrammed, the wipers worked as intended. Safety Recall 3219D describes the issue I had perfecly. My VIN is out of the range of this recall but if I had the same issue as this recall, there might be other bad parts out there and that range might need to be increased.
The contact owns a 2018 Mazda Mazda3. The contact stated that while the vehicle was parked, the contact became aware of a strong fuel odor around the exterior of the vehicle and inside the vehicle. The contact stated that the failure had occurred after refueling. No warning lights were illuminated. The dealer was made aware of the failure, and an appointment was scheduled for a diagnostic test. The dealer had to reschedule the appointment due to a scheduling issue. The vehicle was taken to an independent mechanic, where it was diagnosed with a crack in the top of the fuel pump. The contact was informed that the fuel pump needed to be replaced, and the vehicle was being repaired. The contact referenced an unknown recall with a similar failure; however, the VIN was not associated. The manufacturer was made aware of the failure and a case was filed. The contact was informed that the vehicle needed to be taken to a dealer for a diagnostic test. The repair coverage was denied because the vehicle was not repaired by a dealer. The failure mileage was 179,550.
The Infotainment system is cracking uncontrollably and will make the rear view camera unusable and a safety issue. It keeps resetting every minute. Mazda corporation wont pay for the repair that they are charging about 1,000 to fix it.
My 2018 Mazda 3 has an intermittent electrical failure on the high-speed CAN network that causes multiple safety-critical systems to fail while driving. When the fault occurs, the dash lights up with warnings for powertrain, ABS/traction, lane departure, collision-avoidance, TPMS, immobilizer, and the check-engine light. The car also hesitates or “lurches” between 15–30 mph during these events. At one point in 2024, the vehicle went into limp mode on the freeway, creating a safety hazard. These failures are intermittent but repeatable. Diagnostic scans from 2023–2025 show multiple U-codes for lost communication between control modules; two later became permanent. The issue appears unrelated to any one component and affects many systems at once. The vehicle has been to every Mazda dealership in the North Texas region (Mesquite, Freeman, Hiley, Norm Reeves, Town North). All performed only basic scans; none completed a full CAN-bus or wiring-harness diagnostic. Town North kept the vehicle for six weeks (Sept–Oct 2025), replaced a coil and spark plugs, performed a camera calibration and a TCM update, but the network failures returned within 38 miles. We sought independent inspection only after dealerships repeatedly refused diagnosis whenever the warning lights were not on at the moment of arrival. In November 2025, a technician found significant internal corrosion inside the negative battery cable; touching the cable reproduced the full failure immediately. The corrosion extends deep into the wire sheathing. This appears to be an electrical defect affecting CAN communication and power/ground integrity. When the fault occurs, multiple safety systems disable at once and the vehicle behaves unpredictably. Mazda Corporate has declined further assistance, and the defect remains unresolved. I am filing this report because this is a recurring safety issue that may affect other vehicles of the same model and year.
No incidents
What component or system failed or malfunctioned, and is it available for inspection upon request? The high-pressure fuel pump failed. This component failure prevents the car from starting or staying running. The check engine code confirmed the high-pressure fuel pump failure. The failed component is currently at the Mazda dealership and is available for inspection upon request. How was your safety or the safety of others put at risk The car suddenly stalled while driving on the roadway, creating a dangerous situation. If this had happened on the freeway or in fast-moving traffic, it could have led to a serious accident. Losing power and control of the vehicle at higher speeds poses a major safety risk to both the driver and surrounding vehicles. I was fortunate that the failure occurred on a city street rather than on the freeway. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes. The Mazda dealership inspected the vehicle and confirmed that the high-pressure fuel pump had failed, which was also verified by the check engine code. This failure caused the stalling and starting issues. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives, or others? The vehicle was inspected by an authorized Mazda dealership, which diagnosed and confirmed the high-pressure fuel pump failure. It has not been inspected by police or insurance representatives. Were there any warning lamps, messages, or other symptoms of the problem prior to the failure, and when did they first appear? Before the final failure, the car was hesitant to start, and after it stalled, the check engine light appeared. There were no prior warning messages or signs before the car suddenly stalled while driving. Additional details: The car is only seven years old with approximately 52,000 miles, and it is concerning that such a critical component would fail this early.
The touch screen in my car has developed a malfunction known as “ghost touch,” where the screen glitches and registers inputs I am not making. This failure involves the infotainment system, and the component is still available for inspection upon request. My safety and the safety of others were put at risk because the screen can suddenly change settings, including navigation, phone, and climate controls, while I am driving, which is distracting and dangerous. The problem has not yet been reproduced or confirmed by a dealer or independent service center, nor has the vehicle been inspected by the manufacturer, police, insurance representatives, or others. There were no warning lamps, messages, or other symptoms before the failure—it began suddenly and recently without prior indication.
I got into my car and the infotainment screen was cracked. It had been parked in moderate weather (no extreme heat or cold) and just randomly had multiple small cracks across the screen. This makes the back up camera difficult to see which is a safety concern.
The center dashboard information screen developed "spider cracks" and got opaque in the corners of the screen. The screen would change functions / jump around commands without being touched while driving ( from NAV to radio, change radio stations etc) - apparently called 'Ghost Touch". Mazda has been aware of the defect for some time and issued a TSB ( and settled a class action lawsuit) but we never received any notification. The dealer offered no assistance as the car was out of warranty . We paid several hundred dollars to replace the screen as the car was becoming undriveable.
Wiper stopped functioning, in the rain. Started with the wipers making 2 wipes rapidly, then not functioning. Next day, wipers partially functioned erratically before being stuck in the up position.
The Infotainment system is cracking uncontrollably and will make the rear view camera unusable and a safety issue. Mazda corporation wont pay for the repair that they are charging close to 2k to do.
Touchscreen has the "ghost screen" problem. It has gotten progressively worse over the last year. The Mazda dealership did a firmware update about 2 years ago and that didn't help. Now the screen thinks it's being pressed constantly in the same spot so it just beeps over and over again. If I'm not on my radio, it will hit things like safety settings, emergency contacts, etc. so I have to leave my radio on all the time. I've researched this issue and it's well-known. A recall was issued for 2014-2016 models but not for anything after that.
I have a letter for an important safety recall, re: the backup camera. The letter is dated September 2023, and I called today, after experiencing worsening deterioration of my camera, and I was told that there is currently no fix. So, after 1.5 years, I have no fix for my camera? This is a safety issue
There is a infotainment display that sits on the center part of the dash that has touch screen capability that over time starts to fail and results in what is known as "ghost touch", where random screen settings change as though someone is using the touch screen on the infotainment screen. I had issues to where settings for screen brightness have changed causing my ability to see the controls being hindered and the radio sometimes turning up loudly and then off causing a scare distraction while driving. This screen is also used for the back up camera. There is currently a class action lawsuit for this.
Mazda infotainment system center display screen with spider cracking. Cracking makes part of display unreadable.
The driver side if the door handle metallic wrap has begun peeling, I reached for my door handle and was cut by the wrap as it had torn away from the glued seems. It is small enough to cut my hand but barely visible to the naked eye. I had to put tape over the door handle to prevent further cuts from happening on my fingers. I took 2 photos as soon as the injuries happened and I realized what it was that was causing me to bleed from my scrape. The vehicle currently has a class action suit for the gas fuel pump and i contacted mazda to fix the pump and replace the door handle.
Recall 23V-487 has been un-remedied for over a year. And it sounds like a zip tie would fix it. That's too long.
Mazda has a warranty extension for the 2014-2016 Mazda 3 infotainment touch screen as it may malfunction and glitch. This glitch can be a distraction as the system believes that it is being touched and may cause many things to change in the car such as radio station, navigation setting, and even some vehicle setting accessible from the infotainment screen, causing distractions. However, this issue is also possible on newer 2017 and 2018 models, and there is currently no program to fix the issue. While Mazda may seem like this is not a safety as the touch screen is disabled above 5 MPH, it can still cause distractions when coming to a stop and while stopped which may result in an accident. I think this needs to be resolved and Mazda needs to acknowledge that this touch issue "Ghost Touch" can affect all Mazdas with Mazda Connect 1. Taking this to the dealership to fix is expensive as they want to replace the entire system at a cost of $1000, which I could see many people not doing leading to more dangerous vehicles on the road.
I was parked in a downtown garage, and the vehicle would not start after many attempts, after about 45 minutes of trying (waiting 5 minutes between tries). The engine would turn normally and sounded like it was trying to start, but didn't fully engage. It finally did after 45 mins, and I drove it to the local Mazda dealer in Honolulu. I noticed the check-engine light was on at that time (but not before the incident). They ran a diagnosis, and couldn't replicate the issue, and said it may be a battery problem with low voltage, due to the engine's error codes. But I questioned that since the engine was able to turn normally and adequately at all starting attempts. And the battery was only 2 years old. So I replaced the battery at their recommendation. About 2 hours after picking up the car from the dealer, the same issue happened again. I recorded the issue on my phone this time, and gave it to the dealer. And this time I didn't want to chance it, so had the car towed back to the same dealer. They couldn't replicate the issue immediately, but after several attempts (over a day), they finally experienced it. They said the issue is the fuel pump. I am the original owner, and had purchased the car new from a Mazda dealership, and it has less than 26K miles on it. I researched previous recalls with this same issue on Mazdas, even the same year and model, and it appears to related: [XXX] [XXX] No one was physically harmed due to this issue, but it was certainly a safety risk. If the fuel pump fails while driving, the driver could lose control of the vehicle while in motion. I have attached the invoices for the repairs. I have contacted Mazda Customer Experience and they assigned a case number # [XXX]. However, I was informed that the repairs are unlikely to be covered as there is no open recall on the VIN regarding this issue. Thank you. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
My screen ghost taps (goes into apps without me touching it) plus there is screen damage. I got into my car one day and it looked like the screen was cracked. But it’s on the inside. I never been into the car crash or had any accidents happen to my car or the display. It affects my driving when I am using my back camera
The touchscreen has started to exhibit similar issues as seen in previous recalls for the Mazdas. Commonly known as "ghost touch," the screen receives erroneous inputs, causing settings to change or unwanted functionality to start/stop. Depending on the active screen, the system will exhibit different behavior. In my case, the discoloration is directly at the 6 o'clock position. Whatever application button is there is the one that will be triggered. On a Bluetooth connection, that is the random button. On the AM or FM application, that is the seek button. On the settings menu, that could be any number of important things, including safety systems' settings including the ability to disable traction control. You can see on the display where it has been overheated and is discolored. This is the same location that the "ghost touches" occur. It is intermittent, but occurs more frequently as the unit heats up or after the car warms in an parking lot.
The wipers randomly stopped working. No matter which wiper setting was chosen, the windshield wipers would not activate. I took my car to the nearest Mazda dealer and they fixed it by replacing the Body Control Module.
The contact owns a 2018 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
The radio has a ghost touch that continues to beep and change noise levels without being able to control the radio. This is distracting and is a danger to have this occur while trying to focus on driving.
Over a year later and Mazda is not fulfilling an existing recall despite continuing to pump out new cars: Manufacturer Recall Number6023G NHTSA Recall Number23V-487
The contact’s sister owns a 2018 Mazda Mazda3. The contact stated that while driving at various speeds, the vehicle stalled. The contact also stated that while attempting to depress the accelerator pedal, the vehicle failed to respond as intended. The vehicle was taken to a local dealer where it was diagnosed with a defective fuel pump. The vehicle was repaired, and the contact related the failure to NHTSA Campaign Number: 21V875000 (Fuel System, Gasoline); however, the VIN was not included. The manufacturer was made aware of the failure; however, no assistance was provided. The failure mileage was approximately 51,000.
The collision warning light and lane assistance light come on frequently. It used to just be when the weather was under 40 degrees and the car was cold. However, it now happens all the time. It seems to go on and off for no reason. Additionally, the infotainment system keeps switching radio stations or ghosting without anyone touching it. It also drops Bluetooth connectivity constantly.
The screen/head unit in my car is registering ghost touches. Basically the screen thinks it's being touched even though it isn't. This causes much distraction and hinders the use of the screen because if I try to actual use the head unit, the ghost touch overrides my input which makes it unusable.
Safety Recall 6023G - NHTSA Campaign Number 23V-487. The car was purchased in 2018. On 5/29/2024 the backup camera view has gone black, providing no image. Since I've owned this car, the backup camera view appears, sometimes flickers, and now, has gone completely black, only to "pop" on randomly. I have asked the local Mazda dealer on multiple occasions, since purchasing the car, if it can be repaired/replaced, but am told parts are not available or that there is no "start date" on file. The mechanic has done something to that camera system when the car gets an oil change, and the problem goes away, only to return.
I have seen the problem online called ghosting or ghost control. The infotainment system changes station, settings, selected input or anything else it randomly selects on its own and this is occurring while driving the vehicle.
The infotainment system randomly mutes and unmutes Bluetooth calls; it switches radio stations, skips, and repeats on Spotify and through the settings. It's like the daily turns itself, even though no one touches it. It's startling to have it happen while you're driving, and suddenly, the display starts doing all sorts of crazy changes on its own.
The TPMS light goes off when traveling over 50 MPH, indicating low air pressure on one or more tires. I pulled over, assuming I had a flat; upon visual inspection, everything looked normal. I drove to the nearest air station, checked all four tires, had the proper psi, and reset the TPMS; the light turned off. Then, 10 minutes into the drive, the TPMS light turned on again. I verified again that all tires had the recommended air pressure.
The contact owns a 2018 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention). The contact stated that on several occasions while in reverse (R), the backup camera flickered and was inoperable. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 130,000.
In 2023, the reverse camera would either flicker or completely shut off (displaying a blank screen) while the reverse gear is engaged. While reversing the vehicle to park onto the property the rear camera image failed to display in the vehicle, leading to a collision with the curb. The limited visibility out of the rear windshield for the Mazda 3 leads to a typical driver relying on the camera display to show obstructions not visible through the rear and side mirrors. This failure lead to the car impacting the curb and the passenger being shocked that the car was in an accident. If that was child or small animal, they would have been hit or run over. Luckily, this failure only resulted in property damage, a large dent in the bumper, and possible exhaust damage (see attached). A recall notice for this known Mazda camera issue was sent out in the mail by the manufacturer at the end of 2023. Mazda failed to address the issue when inquired over the phone, instead stating they "Would be in contact once a solution was found." Mazda did not reach out or notify me at any point with a solution until the incident above occurred. After contacting Mazda by phone to address the issue, they said there is still no solution found but to take the vehicle down for a diagnostic test that would be the owner's responsibility to pay for if it was found to be a "owner issue". After a brief discussion and multiple phone calls, Mazda stated they would make the repair as it was confirmed to be a Mazda issue that had just been solved. However, the car would need to be kept over the weekend and a loaner vehicle would be provided. Mazda also stated the collision was a driver issue and Mazda will not be responsible for anything that occurs while using the vehicle. At that point, the dealership was unwilling to assist me and I left. This seems to be a Mazda originating issue, if the rear camera functioned as intended, the curb would have been visible and the impact could have been avoided.
The contact owns a 2018 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was not contacted due to the local dealer going out of business. The manufacturer was made aware of the issue and informed the contact that a second notice would be mailed when the part to do the recall repair was available. The contact had not experienced a failure. VIN tool confirms parts not available.
I’m getting water in my trunk. Dealership replaced left tail light and both lights on the right. The left is dry and the right is soaked again. At least a gallon of water sitting where spare tire is. I’m seeing many other Mazda owners are having the same issue online. This should be a recall. If the water issue doesn’t get fixed it will lead to rusting and mold. My spare tire already is showing rusting.
The contact owns a 2018 Mazda Mazda3. The contact stated that while driving at an undisclosed speed, there was an abnormal sound coming from the engine. The contact stated while starting the vehicle, the abnormal sound would increase. The contact took the vehicle to an independent mechanic who listened to the engine and ended up removing pistons from the engine. The mechanic discovered there was an abnormal sound in cylinder #3 which caused the mechanic to remove the spark plugs. The contact linked the failure to NHTSA Campaign Number: 17V745000 (Engine and Engine Cooling). The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 118,000.
I took my vehicle into RBMC dealership due to the vehicle was experiencing electrical issues and had an open recall / still does. The dealership said I can’t have a dash cam plugged in to a charging port. FCM / LDW / E-Break staying on / throwing error codes = C1001 FSC failure type 97 & U3003 EPB control module power supply failure type 16. They gave me back the car the battery failed the next day and when I called them they banned the VIN of this car to ever return to them. ( the battery was under factory warranty) the issue has only gotten worse and removed my dash cam as they demanded and now I can’t get the car fixed and the issue has gotten worse then taking the car to this dealership less then 30 days ago. They also did not perform the recall when the car was there. The car now has the fallowing codes B13D3 / C1001 / U3003 & possibly more codes because the whole dash is flashing auto light / fcm/ LDW and Break. My [XXX] grandma can’t even take the car in to get fixed the refuse to touch it after it had issues when they gave it back to us and it’s under a extended warranty and was a CPO and has a extended warranty through Mazda. Car only has 31k miles on it and is dangerous for her to drive and myself. Issue has been on going for over a month. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The infotainment screen in this vehicle has internally delaminated causing a well-known "ghosting" problem that causes random buttons to be pressed (without touching the screen) while driving, including volume changes. This results in the system randomly choosing radio stations and turning the volume up to high levels suddenly, distracting the driver and making the screen unusable. Mazda repairs 2014-2016 model year vehicles with this issue under an extended warranty but refuses to do so for 2017+ models.
The contact owns a 2018 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated while driving 40 MPH, the parking brake light illuminated, and the vehicle decelerated and was losing motive power. The contact pressed the parking brake button off and on and the warning light stopped, and the contact was able to drive normally. Additionally, the contact stated that in other instances the forward sensing camera and the lane departure systems were also independently engaging. The contact stated that it was difficult to maintain the lane she was driving in. The contact stated that several unknown warning lights were illuminated. The contact stated that the failure occurred at various speeds. The contact drove the vehicle to a dealer who diagnosed the vehicle and flashed the Powertrain Control Module (PCM). The vehicle was repaired. The contact stated that the failures reoccurred and the battery short-circuited. The contact had taken the vehicle to a non-manufacturer dealer who used a handheld scanner and retrieved the following codes: C1001 Type 97, U3003, and B13D3. The vehicle was not repaired. The failure mileage was 31,321. VIN tool confirms parts not available.
The contact owns a 2018 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while shifted into reverse(R) and reversing out of the driveway, the rearview camera image was flickering on the display screen. The contact stated that the flickering was intermittent but eventually the camera became inoperable. The contact had notified the manufacturer of the failure. The failure mileage was approximately 38,000. VIN tool confirms parts not available.
My car has a faulty Front Body Power Module, a known issue with these cars, but Mazda keeps saying my model is not in the bracket for recalls, they say it's manufactured a day after the cutoff for the recall, so they won't give me recall repair. My windshield wipers aren't working and it's pouring rain, so this is a HUGE danger. I can't afford the $1500+ repair and don't think it's right this is a known issue for this car model and because mine is supposedly 1 day late I don't qualify for the recall care. They expect me to go to a dealership and pay more money for a diagnostic for something that is an issue, and then I have to call corporate again and they'll "Decide" if they'll cover my car or not.
I was driving on the highway in sixth gear and went to down shift to get on to the off ramp and was unable to get it out of sixth gear. I had it towed to the dealer where they were going to charge 4 grand just to tear down the transmission to tell me what might be wrong. So I towed it home and once I was able to get the transmission open, I found the roll pin that connects the shifting shaft to the shift selector plate had worked itself out. If the transmission had been in Neutral, it would have taken less than 20 minutes to fix. But, because it was stuck in gear the whole transmission had to be taken apart.
Touchscreen in vehicle is randomly changing without my touching the screen. This is a well-documented issue in other 2014-2016 Mazdas for which a recall has been previously issued. However, my vehicle also experiences this same issue ("ghost touch") which indicates to me that the problem is not just limited to 2014-2016 vehicles and that my 2018 Mazda should be included in the original recall to replace the defective touchscreen. The random operation of the touchscreen is a safety hazard and should be immediately recalled by Mazda.
The entertainment/navigation screen randomly started developing spidering cracks on the inside of the screen and has grown exponentially. It is getting close to the point where the screen is not readable and becoming useless. I have done research and have seen that many other Mazda owners have experienced the same issue where their screens cracked from the inside rendering it useless but Mazda refuses to cover the cost of an issue that is not caused by any Mazda owner. Without this screen, I would need to hold my phone in order to use a navigation app to get around or attempt to find a phone holder so I can still get around successfully.
Fuel smell after a fill-up, fuel pump is cracked/deformed EXACTLY as described in Mazda bulletin 5321K (THIS BULLETIN EXCLUDES THIS MODEL). Strong fuel smell in the cabin, liquid fuel leaking from the top of the tank.
There is a known issue with the infotainment system referred to as ghost tough. This causes the system to randomly change stations/songs, etc while the car is in motion. There is also a delamination issue. Mazda issued a recall for 2014-2016 vehicles, however a quick internet search shows that this issue continues to be a problem. This issue can be extremely distracting as the driver attempts to stop the system from changing.
The contact owns a 2018 Mazda Mazda3. The contact stated that while his girlfriend was driving at 65 MPH, several unknown warning lights illuminated, and the vehicle stalled. The contact stated that his girlfriend was able to safely drive the vehicle to her destination. The vehicle was then towed to the dealer. The vehicle was diagnosed with rod knocks. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 105,000.
The contact owns a 2018 Mazda Mazda3. The contact stated while driving 60 MPH, the vehicle inadvertently lost motive power. After restarting the vehicle, the vehicle returned to normal functionality. No warning lights were illuminated. The vehicle was towed to an independent mechanic, who was unable to determine the cause of the failure. The vehicle was then towed to the dealer, who determined that there was no oil in the engine. The manufacturer was not notified of the failure. The failure mileage was 105,000.
I became aware of this recall for my backup camera and one day i closed my trunk wasnt expecting it too affect my car but it did!! the rear backup camera was flickering and distorted as i was back out of a parking spot and almost got rear ended by someone and mazda told me by the middle of january they should have a fix for this its a camera and a wiring harness and fastener no need to have too wait this long for something that can cause a major accident its not only happened once but twice out of nowhere i have pictures and video recordings of it!!
Data synced from NHTSA on May 4, 2026