2016 GMC Yukon

Ticking sound coming from engine, possible damaged camshaft lobe due to lifter roller failure. It can cause sudden engine failure, significant power loss, and unexpected stalling while driving, increasing crash risks. The issue is linked to AFM (Active Fuel Management) system failures. The problem has been diagnosed by dealer service department. No warning lamp or message, problem first appeared 7 April 2026.

Vehicle been in the shop 3 times. [XXX] suspension light repeat come on. Working with warranty company. Light came on again 3 more times after Vehicle left the shop INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The suspension service lights repeatedly coming on.

When making a slow turn in drive or reverse the park assist screen shows it’s not working. Then all screens in the car turn black and the steering locks while driving. Making it impossible to turn or move. This is happening while driving, while parking. Putting my safety and others at risk due to not being able to control the steering. Park assist failure screen pops up then all screens turn black. Car is still on just unable to move. I have not had it checked by a mechanic yet.

Misfire then replaced plugs,coils and wires, then change fuel injector, and problem still there, then started truck and was tossing power and motor started ticking. Every shop told me this is the same common problem they're having with all 6.2L engine and they're all on recall by GM. I know 2016 are not in recall but I think they should be because this problem is in all 6.2L engine

On [XXX], while idling in my driveway the engine abruptly stopped with a loud clunk and refused to turn over when I attempted to restart it. The vehicle was towed to Bergstrom GMC in Appleton WI. Upon inspection it was determined that a connecting rod and crankshaft bearing had failed requiring replacement of the engine. The vehicle has a 6.2-litre V-8 engine with 106,000 miles on it. The vehicle is currently still at the dealership waiting for the engine replacement at an estimated cost of $18,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

THE fuel pressure line from the fuel pump to the flex fuel sensor chaffed a pin hole leak near the front top of the fuel tank. This caused a significant fuel smell and trace leak at the front of the fuel tank which could lead to a fire or explosion. The new hose has a longer chaffing covering leading me to believe gm knew about this issue. vehicle has 127,000 miles. I feel gm should reimburse me for this repair as a fuel line should not have ever chaffed through and leaked.

The LED left turn signal and blind spot detection ( safety feature) on the left outside rear view mirror suddenly stopped working. The is a TSB for warranty for 2016-2018 GM YUKON (#10-08-64-002D) and it states that the bulletin has been revised to include 2016-2018 year models for this defect. I am starting this claim because I am told by GM that my VIN is not covered under this warranty, yet I am experiencing the same issue stated in the TSB listed above.

The contact owns a 2016 GMC Yukon. The contact stated while driving 70 MPH, and attempting to accelerate, the vehicle jerked, then briefly lost motive power before the engine seized. The contact was able to coast to the side of the road. The transmission warning light was illuminated. The vehicle failed to restart. The vehicle was towed to a friend's residence. The vehicle was not diagnosed or repaired for the most recent failure. Days before the failure, the vehicle jerked while driving at various speeds. The vehicle was taken to Auto Zone; however, no cause for the failure was found. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 143,000.

Engine light keeps appearing and when checked it shows catalytic converter needs replaces and its sensors need replaced. Brake light has short in it and I repaireable

TRANSMISSION SHUDDERS, LURCHES FORWARD UNCONTROLABLY, AND HARD SHIFTS

The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly downshifted with the check engine warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed that the transmission had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 250,000.

A side detection module pin was corroded and was disrupting the electrical signals to major vehicle components, such as the dash (DIC). The DIC would lose communication with the rest of the vehicle while driving so no vehicle operation data was visible such as speed, alerts messages, etc. This likely also caused engine failure due to the incorrect operation of the afm which is on the same electrical circuit. No warning messages were given. The bad side detection module was diagnosed and fixed at a dealer and shortly after engine issues were noticed.

The contact owns a 2016 GMC Yukon. The contact stated that while driving at 65 MPH and attempting to accelerate, the vehicle briefly shuddered before returning to normal functionality. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the torque converter. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.

On two occasions while driving at low speed, my vehicle braked on its on a pulled hard to the left; the stabilitrac indicator also popped on briefly. I went online to determine if there were any recalls on my vehicle and found that one of the recalls on the 2016 Yukon was the exact issue happening with my vehicle. I checked my VIN and found that my vehicle was not one of the vehicles with this issue. I called GM to see if my vehicle had just not been published yet. I explain the situation too the customer service person; she understood my situation and informed me that until my specific VIN in identified with this issue, there's nothing that can be done. I'm thinking that until an accident happen because of this issue, there is nothing that can be done. I read that my issue was a problem with the EBCM, which needs to be reprogrammed. I thank you for any assistance with this issue.

There's alot of time while I'm driving in line going slowly and break pedal become hard and it will seem like the truck it's not stopping.

2 months ago our 16 gmc Yukon Denali 6.2 bent a push rod on cylinder 4 . So had to fix it when I took out DOD lifters put them on work bench and about 10 minutes out the DOD lifters flew apart and know having transmission issues it’s starting to shudder ! So I would liked the [XXX] thing recalled because engine still isn’t right either it only has 130000 miles. I’ll never buy a [XXX] gmc because of problems! I want the [XXX] thing fixed ASAP we paid to much money for it to be having problems!!!! Please send a recall letter to fix it ! [XXX] . 4/29/2025 6:53 p:m INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Without warning, giving vehicle low consistent pressure on gas pedal to move forward slowly (2-3mph) vehicle rpm jumped up then suddenly shifted and vehicle jerked forward in a school zone. Behavior continued and vehicle was ultimately towed.

I WAS DRIVING MY CAR MONDAY AND I ALMOST CRASH WITH THE CAR IN FRONT OF ME THE BRAKES DOESNT WORK AND THEN IN THE PANEL START LIGHTS OF THE ENGINE THE SUPENSION LIGHT AND SIGH SAYING BRAKE ASISTANT, THE CAR IS PARK BECAUSE THE BRAKES AND I LOOK FOR RECALLS AND I CALL GMC AND THEY SAYS THAT I DONT HAVE ANY RECALL BUT I ALMOST DIE MONDAY BECAUSE THE VACUM PUMP FOR THE BRAKES FAIL AND ALL THE LIGHTS IN THE PANNEL START LIGHT UP.

My brakes are not working properly. I can be backing up and put my foot on the brake. My truck will keep moving until I apply a lot of pressure on the brake pedal. I can be backing up and my truck will automatically brake and stop moving. I have to cut the truck off, start it back up for it to move. I was in a stand still traffic jam and braking a lot and my truck did stop it keep rolling. Sometimes when I apply the brake it slides.. This is the third time I have put it in the shop. I changed the brakes, brake sensor and replaced tires. I am scared to drive it. My truck is currently in the shop now for the brakes. please help.