2012 Toyota Prius

My Brake Booster/Actuator failed on me while on the freeway with out any warnings. It made it really hard to stop the car. I didn't find out what it was untill I took it into a repair shop and they told me it was the Brake Booster/Actuator.

The vehicle is experiencing a suspected brake actuator / brake booster failure. Multiple warning lights appeared simultaneously, including ABS, Brake, Traction Control, and Master Warning lights. The vehicle produces a frequent buzzing noise from the brake system, especially at low speeds or when stopped. The noise occurs repeatedly when pressing the brake pedal, indicating the system is struggling to maintain hydraulic pressure. This condition raises serious safety concerns because it may reduce braking performance and increase stopping distance. Brake system failures present a significant risk to vehicle occupants and others on the road. After researching the issue, I learned this appears to be a common failure in Toyota Prius vehicles of similar model years, and Toyota previously issued extended warranty coverage for the brake booster/actuator assemblies. However, many vehicles now exceed the coverage limits despite the safety nature of the defect. I am submitting this complaint because a failing brake system is a critical safety hazard, and this issue appears widespread.

Vehicle check engine code C1391 (Antilock Brake System - abnormal leak in accumulator) came up on 2/5/2026. Recommended repair is to replace the Brake Booster Pump and Assembly, Brake Booster - over $1000 in parts alone. This WAS covered by an Extended Warranty by Toyota (10 years / 150K miles). I only have 120K miles at this time but am past the 10 year mark. However, it seems that this part will fail in every Prius given time and encourage NHTSA to monitor these failures and hold Toyota accountable to address post the 10 year / 150K mile mark.

Vehicle: 2012 Toyota Prius Mileage: Approximately 217,000 miles While driving normally in traffic, the vehicle experienced a sudden and unexpected brake system failure. Multiple warning lights illuminated simultaneously, including the red BRAKE warning light, ABS warning light, traction control light, and warning symbol (!). Shortly after, the vehicle began emitting an audible warning/beeping, and there was a sudden loss of power brake assist. The brake pedal behavior changed abruptly: the pedal became very soft initially, then became suddenly hard halfway through travel, This failure occurred while approaching another vehicle in traffic, and I narrowly avoided rear-ending the vehicle in front of me. The unexpected loss of brake assist created an immediate and dangerous situation, as the vehicle did not decelerate as expected when the brake pedal was applied. Due to the seriousness of the brake failure and safety risk, the vehicle was removed from service and towed. This incident represents a critical safety defect, as sudden loss of braking assist while driving poses a significant risk to vehicle occupants and other road users. I am reporting this incident to document the hazard and request investigation into the reliability and safety of the brake system design. I am requesting you to please issue a recall and reimburse me , as these parts are very expensive , it affected my financial situation, Thanks

Odometer Fraud. The contact purchased a 2012 Toyota Prius. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 187,000, and at the time of registration, it was discovered that the mileage was 227,000.

The contact owns a 2012 Toyota Prius. The contact stated while driving at an undisclosed speed, several unknown warning lights illuminated, with an abnormal sound coming from the vehicle. The vehicle was taken to the dealer where it was diagnosed with brake booster failure. The contact was informed that the brake booster pump needed to be replaced. The vehicle was not repaired. The contact stated that the failure was a known failure with the vehicle. The manufacturer was made aware of the failure. The contact was informed that an undisclosed Extended Warranty Program had expired. In addition, the contact was informed that the repair was not covered. The failure mileage was approximately 175,000.

While driving, the vehicle experienced a sudden brake system malfunction without prior warning or gradual degradation. The vehicle was being operated under normal driving, road, and weather conditions. No recent brake service, repairs, or aftermarket modifications had been performed prior to the failure. Multiple warning lights illuminated on the dashboard, including the ABS warning light, brake warning light, and traction control warning light. Shortly after the warning lights appeared, the vehicle began emitting continuous warning beeps. Audible buzzing or pumping noises were also present from the brake system during the malfunction. During this event, brake performance was reduced and braking felt inconsistent. The brake pedal became hard at times and spongy at other times, requiring increased effort to slow the vehicle and resulting in unpredictable braking response. This created a safety concern while the vehicle was in motion. The driver was forced to alter driving behavior and exercise extreme caution due to reduced braking confidence and unpredictable pedal feel. The malfunction has occurred intermittently during normal driving. The condition temporarily resolves on its own and later reoccurs without corrective action. The suspected failed component is the brake actuator / ABS actuator assembly. A diagnostic scan retrieved fault codes C1252 (Brake Booster Pump Motor ON Time Abnormally Long), C1253 (Pump Motor Relay Malfunction), and C1256 (Accumulator Low Pressure), which are consistent with brake actuator malfunction. The failure occurred at approximately 154,000 miles. This vehicle model and generation have a documented history of premature brake actuator failures with similar safety-related symptoms reported by other owners. The condition places the driver and others at risk due to unpredictable braking behavior, reduced braking effectiveness, and repeated warning alarms while driving. Warning lamps and audible alerts continue intermittently.

The contact owns a 2012 Toyota Prius. The contact stated that while reversing, the driver's side rear wheel flipped over. The vehicle was towed to the dealer, where it was diagnosed with a corroded I-Beam assembly on the rear wheel. The contact was informed that the driver's side rear hub and the BRG assembly, rear suspension, and bolts needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 196,347.

Odometer Fraud. The contact’s son recently purchased a 2012 Toyota Prius. The vehicle was a private sale. After the purchase, it was discovered that there was a mileage discrepancy based on the Carfax report. At the time of purchase, the vehicle displayed 137,000 miles. However, the Carfax report listed the mileage as 281,586 miles, and the current mileage on the vehicle was 151,103.

My 2012 Toyota Prius plug in hybrid had just passed state inspections and was even looked at by a dealership a year ago with no reported issues. I brought up a whirring issue at the dealership when breaking but the dealership said that’s normal for a hybrid. In a matter of minutes while driving, the traction light, brake light, and ABS light came on as well as a groaning, whirring sound when breaking. Over time, the breaks failed and I could not stop the car, almost causing a wreck because I could not stop without putting all my body weight on the break pedal. When taking it to the Toyota dealership for a whole diagnostic, they said it was a break actuator and break booster failure that is known to happen with Prius’s. They quoted me $3000 for a repair and then marked my breaks as yellow not red on their sheet implying I could still drive it despite the dangerous situation of driving without functioning breaks. When looking into it, this seems to be a known and common problem with Prius’s due to a faulty manufactured part. Codes were c1391, wc1256, and c1252. I believe this part should be recalled and Toyota should fix these faulty parts, especially considering they inspected my car and did not mention it as an issue despite it being a known issue. I got a second opinion from Mavis Tires and they concurred with the diagnosis but could not fix it.

The hybrid system fails to enter “Ready” mode with no SMR engagement audible from the junction box. Dashboard displays ABS, brake, engine, and master warning lights. OBD codes include U0142, U0155, and previously U0073 . Rear brake lights function normally when pedal is pressed. Dealer said to pay 250$ for diagnostic and diagnosed incorrect voltage from brake light switch and quoted $348.94 to replace, but refused to proceed with open safety recall J0V / 18V684 (NHTSA 18V684000) citing inability to achieve “Ready” mode. Recall covers inverter failure leading to loss of motive power. Dealer declined to jump 12V battery or use external power to perform required software update and inverter inspection. Vehicle remains inoperable and poses safety risk due to sudden power loss potential. Component (inverter G9200-47141) available for inspection. Problem confirmed by dealer diagnostics. No police or insurance inspection. Warning lamps appeared after 12V battery replacement three months ago.

While driving 60 mph in highway, ABS, traction control and brake lights lit up and vehicle lost its effective braking power. There were no prior warnings prior to this failure. It was a sudden incident. Since it wasn't rush hour, I could safely reduce speed and bring the car to stop. Situation could have been much different if it was normal hours. After taking the car to dealership, it indicated DTC code 1391, Brake Assembly Failure. The car was fixed at dealership at cost of $3,000. When researched further, it appeared that there is broader pattern of failures. Numerous reports have been made by owners of 2010–2015 Toyota Prius, Prius PHV, 2012–2015 Prius V, 2012–2014 Camry Hybrid, and 2013–2015 Avalon Hybrid vehicles, all of which share the same brake booster pump assembly design manufactured by Advics Co., Ltd. Dealerships, including Capistrano Toyota and Claremont Toyota in California, have previously petitioned NHTSA regarding this very defect. Their 2019 letter to the agency documented that Toyota: * Knowingly excluded hundreds of thousands of hybrids from prior safety recalls (DOH 13V-235 and KOL 19V-544) despite identical failures. *Issued “post-failure” repair programs (Warranty Enhancements ZJB, ZKK, ZKC, ZLM, 20LE03, 23TE06 and 23TE07) only after owners experienced brake failure. * Identified the same DTC codes (C1252, C1253, C1256, C1391, U0293) in both recalled and unrecalled vehicles—codes that correspond to accumulator leaks, loss of brake pressure, and failure of brake assist and stability control systems. * Admitted through Technical Service Bulletin TSB-0130-19 that these defects caused loss of hydraulic pressure, increased stopping distance, and total loss of brake assist in affected hybrids. In short, the defect pattern across multiple hybrid models is identical to those already recognized by Toyota and NHTSA under prior recall campaigns, but for reasons unexplained, Toyota limited the recall population and left many consumers unprotected

Traction control.Abs and brake warning lights all came on.

2012 Toyota Prius. The brake system malfunctioned and my daughter was almost in a wreck. The ABS, traction control, and brake warning lights on the bashboard all illuminated at the same time. The brake pedal feels soft and is less responsive requiring more effort to stop the vehicle. The brake actuator assembly is making a hissing noise. Ran a ABS test using a scan tool and received a C1391 error code. The Code points to a leak within the brake actuator system. Upon research I have found that this is a very common and costly repair that Toyota has known about for many years. Toyota issued a customer support program related to this issue that ran for 10 years or 150,000 miles from the vehicle's date of first use. This car, being a 2012, is beyond the support program. I contacted Toyota, hoping they would do the right thing and cover the repair. I was told that they would not cover the repair or supply the parts to cover the repair. I told the Rep. for Toyota that I did not feel like it was fair for Toyota to continue to put millions of drivers at risk for a product that they clearly realize for years now is defective and could hurt or kill someone. The code and the braking issue did not appear until after the customer support program ended and therefore we had no warning or way to anticipate this braking issue or the danger to my daughter and anyone else riding with her in the car or on the roadway near her travel routes. I traveled 300 miles, rented a Uhaul car tow trailer and brought the car back home. My mechanic confirmed the code C1391 and the fact that the brake actuator has failed. The mechanic has ordered the parts (the same defective parts) to replace the broken ones. Toyota is still selling the same part as a replacement part clearly knowing that it is not safe and no warning came with the replacement part explaining the potential for a braking issue. Based on internet research this same part is in many 2005 to 2013 Toyota and Lexus

While driving on a city road below the speed limit, braking was compromised leading to loss of traction and failure of the ABS system. During the incident, the brake, ABS, and engine warning lights all turned on and a collision was only avoided due to pumping of the brakes. Further investigation by a mechanic revealed a failure of the brake actuator system. Failure of this system has increased the stopping distance of the vehicle considerably and makes braking unreliable and unpredictable.

The contact owns a 2012 Toyota Prius. The contact stated that while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated that the check engine and the hybrid warning lights were illuminated, and the vehicle decelerated. The contact received notification of NHTSA Campaign Number: 18V684000 (Hybrid Propulsion System). The vehicle was taken to the dealer; however, the contact was informed that parts were not yet available for the recall repair. The contact was informed that the parts might be available within a week. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 137,000.

Brake getting stuck on the floor would have to press on brake really hard just to get a response, this will happen out of the blue! Driving in highway or just driving off the driveway. I almost hit a car in front of me due to lack of brake, i had to swerve to the side! First appear 1 day after buying the car..This issue needs to be worked on right away.

While driving on the freeway I applied the brakes and the brakes suddenly felt soft and not very responsive. At that moment 3 dashboard lights turned on: ABS, BRAKE, and the slip indicator lights. I carefully got out of the freeway, parked the car, and had the car towed to an independent mechanic. The mechanic detected brake booster and actuator problems, code C1391.

Brake Actuator and ABS Accumalator failed. It is a common failure reported by multiple owners on these cars. I was on the high way going 70 when it failed and lost any brake boost I had putting me in a very dangerous situation where I narrowly avoided an accident. Upon scanning the car's codes I got code C1391 which I looked up and saw a bunch of other people who were also struggling with this issue.

While driving on the interstate I went to slow down to merge and my brakes failed. The following warning lights came on: Master Warning Light (yellow), Brake System Warning Light, Brake System warning light (red), ABS Warning Light, and the Slip Indicator light. My vehicle was towed to a Toyota Dealership and after running a diagnostic test, they confirmed that it was the "Break booster with accumulator c1391 stored internal leak of accumulator and need immediate attention" which they quoted at $4,295.68 to fix. After researching the issue saw A Customer Support Program 20TE07 was issued taking responsibility for the faulty Brake Booster Pump Assembly however only covered the repair for a two-year period and only if it was one of the identified diagnostic trouble codes listed in the CSP issued by Toyota but expired in Feb 2022. The code pulled from my vehicle 3 days ago was listed in this document, but the coverage only covers until Feb 2022. This is not a normal wear and tear issue, it is a faulty part that Toyota identified as a life and death safety concern but refuses to do anything about because mine didn't show an issue within their 2-year CSP timeframe. Toyota identified that there are roughly 118,950 2012-2014 model year prius V with a production period of late September 2010 to mid-November 2014 vehicles that this faulty part affects along with everyone else on the road with these vehicles as it causes failure of the brake booster pump assembly, which leads to a loss of braking assist and the deactivation of the Vehicle Stability Control system. For the safety and lives of the owners of these vehicles and all of the other lives of the drivers on the road that this could affect in the case of this faulty part should there be a catastrophic accident, like mine could have been, a nationwide recall on this part MUST be issued.